Huawei NetCol5000-C030 Series User Manual Download Page 118

Page: 118 / 215

4.5.5 Correlation Relationship of Parameters

When setting parameters, pay attention to the following relationships.

Alarm Parameters

●

Supply air high temperature alarm thr 5°C ≤ Return air high

temperature alarm threshold

●

Supply air high temperature alarm thr 5°C ≤ Hot aisle high

temperature alarm threshold

●

Cold aisle high temperature alarm thr 5°C ≤ Hot aisle high

temperature alarm threshold

●

Cold aisle high temperature alarm thr 5°C ≤ Return air high

temperature alarm threshold

●

Supply air low temperature alarm thr 5°C ≤ Return air low

temperature alarm threshold

●

Supply air low temperature alarm thr 5°C ≤ Hot aisle low

temperature alarm threshold

●

Cold aisle low temperature alarm thr 5°C ≤ Hot aisle low temperature

alarm threshold

●

Cold aisle low temperature alarm thr 5°C ≤ Return air low

temperature alarm threshold

Parameters of Teamwork Settings

Number of smart cooling products in this group ≥ Number of running smart

cooling products in this group

Parameters of Cooling Cap. Mgt.

Upper limit of water supply temperature > Lower limit of water supply

temperature

Parameters of Indoor Fan

●

Min indoor fan speed ≤ Min indoor fan speed in silent mode ≤ Medium indoor

fan speed in silent mode ≤ Max indoor fan speed in silent mode ≤ Max indoor

fan speed

●

Min return/supply air temp difference in silent mode ≤ Medium return/supply

air temp difference in silent mode ≤ Max return/supply air temp difference in

silent mode

●

Min indoor fan speed ≤ Min speed for humidifying ≤ Max indoor fan speed

●

Min indoor fan speed ≤ Lower limit of max speed for dehumidifying ≤ Upper

limit of max speed for dehumidifying ≤ Max indoor fan speed

●

Indoor fan min return/supply air temperature difference ≤ Indoor fan max

return/supply air temperature difference

●

Only when Air-side difference pressure sensor type is set to 0~50Pa or

Differential pressure sharing is enabled, Indoor fan control type can be set

to Pressure diff ctrl.

NetCol5000-C(030, 032, 065) In-row Chilled Water

Smart Cooling Product

User Manual

4 Power-On Commissioning

Issue 04 (2021-03-15)

110

Summary of Contents for NetCol5000-C030 Series
























































































































































































































Search results

Summary of Contents for NetCol5000-C030 Series

Reviews:

Related manuals for NetCol5000-C030 Series

Brands by name

Popular brands

Huawei NetCol5000-C030 Series, User Manual

Search results

Summary of Contents for NetCol5000-C030 Series

Reviews:

Related manuals for NetCol5000-C030 Series

Brands by name

Popular brands