manualshive.com logo in svg

Huawei NetCol5000-C030 Series, User Manual

Introducing the Huawei NetCol5000-C030 Series, a cutting-edge cooling solution for data centers. Enhance your facility's efficiency with our state-of-the-art product. To swiftly set up and optimize your cooling system, download the comprehensive and free Quick Manual from manualshive.com. Experience seamless operations with this user-friendly manual at your fingertips.

Share
Download
background image

Function

Description

Power

management

A comprehensive power management function is provided.

Faults such as power reverse phase, open phase, overvoltage,

undervoltage, high frequency, and low frequency are diagnosed

and alarms are reported and recorded. Automatic protection,

recovery, and restart are also provided.

 

Features

●

The display panel provides a touchscreen with a user-friendly interface.

●

The controller is highly precise and responsive.

●

The display panel is protected by a multi-level password protection

mechanism to avoid misoperation.

●

The password is verified each time the system is started or shut down to

ensure system operation security.

●

The controller provides functions such as automatic recovery after power

failure and water leakage detection, improving the system reliability.

●

The cooling capacity, air volume, as well as the operating status and time of

each component in the device are displayed on the display module in real

time.

●

Multiple display languages are supported.

●

O&M personnel can export fault records in one-click mode, making it easy to

operate the device and know the running status of the device.

●

The device supports communications protocols such as Modbus RTU, Modbus

TCP, and SNMP, facilitating connection to the network management system.

●

The display panel intelligently identifies abnormal parameter settings

(incorrect commands) and rejects them automatically.

●

If the indoor temperature fluctuates beyond the normal range, an audible and

visible alarm signal is produced automatically.

2.4.3 Monitoring System

The monitoring system provides logic control, data collection, control demand

delivering, alarm reporting, data storage, user right management, and teamwork

control. You can connect the smart cooling product monitoring system to your

monitoring system over a northbound communications port to perform remote

management. The smart cooling product supports remote management ports and

provides RS485 ports and FE ports to support Modbus-RTU, Modbus-TCP and

SNMP for real-time data collection and alarm reporting.
Smart cooling products can be networked over the CAN bus to realize teamwork

control, energy conservation, and service life extension.

NetCol5000-C(030, 032, 065) In-row Chilled Water

Smart Cooling Product

User Manual

2 Product Description

Issue 04 (2021-03-15)

Copyright © Huawei Technologies Co., Ltd.

22

Summary of Contents for NetCol5000-C030 Series
























































































































































































































Reviews:

No comments

Related manuals for NetCol5000-C030 Series

Dakota Digital 2000 Series Parts List preview
2000 Series
Brand: Dakota Digital Pages: 38
Paradyne 8820 Installation Manual preview
8820
Brand: Paradyne Pages: 86
Davis Instruments 8127 Installation Instructions Manual preview
8127
Brand: Davis Instruments Pages: 16
AA Products X31 Instruction Manual preview
X31
Brand: AA Products Pages: 6
D-2 Incorporated JF-1A Installation & Safe Use Manual preview
JF-1A
Brand: D-2 Incorporated Pages: 28
D+H WRZ Original Instructions Manual preview
WRZ
Brand: D+H Pages: 12
GBC AdvancedPunch Pro Operation & Instruction Manual preview
AdvancedPunch Pro
Brand: GBC Pages: 92
BAFANG M510 User Manual preview
M510
Brand: BAFANG Pages: 4
Oki OKICOLOR8n Replacement Instructions preview
OKICOLOR8n
Brand: Oki Pages: 4
Vega VEGABAR 81 Quick Setup Manual preview
VEGABAR 81
Brand: Vega Pages: 20
Vega SOLITRAC 31 Operating Instructions Manual preview
SOLITRAC 31
Brand: Vega Pages: 88
Vega MINITRAC 31 Quick Setup Manual preview
MINITRAC 31
Brand: Vega Pages: 28
Vega vegaflex 83 Operating Instruction preview
vegaflex 83
Brand: Vega Pages: 92
Öhlins YA 559 Mounting Instructions preview
YA 559
Brand: Öhlins Pages: 8
AccuAir AA-4397 Installation Manual preview
AA-4397
Brand: AccuAir Pages: 40
Peak PKC0RG Owner'S Manual preview
PKC0RG
Brand: Peak Pages: 10
Insignia NS-DCLR42X5 Quick Setup Manual preview
NS-DCLR42X5
Brand: Insignia Pages: 2
PolyScience F25N0A101B Operator'S Manual preview
F25N0A101B
Brand: PolyScience Pages: 14

Brands by name

Popular brands

Load more brands