manualshive.com logo in svg

Huawei NetCol5000-C030 Series, User Manual

Introducing the Huawei NetCol5000-C030 Series, a cutting-edge cooling solution for data centers. Enhance your facility's efficiency with our state-of-the-art product. To swiftly set up and optimize your cooling system, download the comprehensive and free Quick Manual from manualshive.com. Experience seamless operations with this user-friendly manual at your fingertips.

Share
Download
background image

Alarm ID

Alarm Name

Alarm

Severity

Possible Cause

Solution

A105-01

Indoor fan failure

alarm

Critical

● The accumulated

runtime of the fan

exceeds the alarm

threshold.

● The cable to the

fan is not

connected properly.

● The power supply

to the fan is

abnormal.

1. Maintain or replace

the fan, and clear

the accumulated

runtime.

2. Check the cable

connection to the

fan.

3. Check the power

supply to the fan.

A118-01

Primary power failure

alarm

Major

The power supply is

faulty.

Check the power

supply.

A130-01

Humid water inlet

solenoid valve fault

Major

● The cables to the

water inlet solenoid

valve are loose or

damaged.

● The water inlet

solenoid valve is

faulty.

1. Check the cables to

the water inlet

solenoid valve.

2. Replace the water

inlet solenoid valve.

A193-01

Air-side diff pressure

sensor fault

Major

● The cable to the

differential pressure

sensor is loose or

damaged.

● The pressure tube

of the differential

pressure sensor is

reversely

connected.

● The differential

pressure sensor is

faulty.

1. Check the cable

connection to the

differential pressure

sensor.

2. Check the tube

connection to the

differential pressure

sensor.

3. Maintain or replace

the differential

pressure sensor.

A220-01

Wizard startup is in

progress

Warning

Wizard startup is in

progress.

Wait until wizard

startup is complete or

clear the alarm

manually to exit

wizard startup.

A233-01

Air-side low pressure

difference alarm

Warning

● Contained aisles

are poorly-sealed.

● The differential

pressure sensor is

faulty.

1. Check that the cold

and hot aisles are

well-sealed.

2. Maintain or replace

the differential

pressure sensor.

NetCol5000-C(030, 032, 065) In-row Chilled Water

Smart Cooling Product

User Manual

6 System Operation and Maintenance

Issue 04 (2021-03-15)

Copyright © Huawei Technologies Co., Ltd.

147

Summary of Contents for NetCol5000-C030 Series
























































































































































































































Reviews:

No comments

Related manuals for NetCol5000-C030 Series

Mamiya 645 Instructions preview
645
Brand: Mamiya Pages: 4
NEC NP2200 Series Installation And Assembly Manual preview
NP2200 Series
Brand: NEC Pages: 9
NEC NP-M260W Installation And Assembly preview
NP-M260W
Brand: NEC Pages: 3
Kabuto FLAIR Instruction Manual preview
FLAIR
Brand: Kabuto Pages: 25
Baicells Nova-233 G2 Installation Installation preview
Nova-233 G2
Brand: Baicells Pages: 32
BAFANG C965 Manual preview
C965
Brand: BAFANG Pages: 18
VANPOWERS DP C240.CAN User Manual preview
DP C240.CAN
Brand: VANPOWERS Pages: 23
Bartington Mag648 Operation Manual preview
Mag648
Brand: Bartington Pages: 11
DBI SALA Exofit Instructions Manual preview
Exofit
Brand: DBI SALA Pages: 32
Hach 3700 Series Basic User Manual preview
3700 Series
Brand: Hach Pages: 148
IFO 8263 Instruction Manual preview
8263
Brand: IFO Pages: 8
Warrior Products 3860 Quick Start Manual preview
3860
Brand: Warrior Products Pages: 2
Salta 532 Assembly Instructions Manual preview
532
Brand: Salta Pages: 91
X Rocker Gaming Chair User Manual preview
Gaming Chair
Brand: X Rocker Pages: 12
Miditech AUDIOLINK II Owner'S Manual preview
AUDIOLINK II
Brand: Miditech Pages: 11
Vortice Kit Vario CO2 Instruction Booklet preview
Kit Vario CO2
Brand: Vortice Pages: 132
Heitronic 4002940450170 Installation And Operating Instructions Manual preview
4002940450170
Brand: Heitronic Pages: 12
Trust Dual Shock Rally Master User Manual preview
Dual Shock Rally Master
Brand: Trust Pages: 9

Brands by name

Popular brands

Load more brands