Huawei NetCol5000-C030 Series User Manual Download Page 78

Page: 78 / 215

NO TICE

Exercise caution while connecting cables. Prepare protective tools in advance.

Figure 3-52 Connecting power cables (NetCol5000-C065)

Figure 3-53 Connecting power cables (NetCol5000-C030/C032)

1. Remove screws from both ends of the clip to remove it.
2. Connect the cables with crimped terminals to the L, N, and PE.

NO TE

NetCol5000-C065 uses a common screwdriver to secure the cables, NetCol5000-C030/

C032 uses a 100-120 mm screwdriver to secure the cables.

3. Place the connected power cables vertically, use the clip to secure them in a

proper position, and use screws to secure the clip.

4. Fasten the power cable to the vertical pillar by cable ties every 150 mm to

200 mm.

Step 4 Use a multimeter to check for a short circuit between L and N of AC1 and AC2.

Use a multimeter to check for a short circuit between L, N, and PE.

NetCol5000-C(030, 032, 065) In-row Chilled Water

Smart Cooling Product

User Manual

3 Installation

Issue 04 (2021-03-15)

Summary of Contents for NetCol5000-C030 Series
























































































































































































































Search results

Summary of Contents for NetCol5000-C030 Series

Reviews:

Related manuals for NetCol5000-C030 Series

Brands by name

Popular brands

Huawei NetCol5000-C030 Series, User Manual

Search results

Summary of Contents for NetCol5000-C030 Series

Reviews:

Related manuals for NetCol5000-C030 Series

Brands by name

Popular brands