manualshive.com logo in svg

Huawei NetCol5000-C030 Series, User Manual

Introducing the Huawei NetCol5000-C030 Series, a cutting-edge cooling solution for data centers. Enhance your facility's efficiency with our state-of-the-art product. To swiftly set up and optimize your cooling system, download the comprehensive and free Quick Manual from manualshive.com. Experience seamless operations with this user-friendly manual at your fingertips.

Share
Download
background image

NO TICE

Exercise caution because the device is still energized after it is shut down on the

screen of the display module.

Step 2 Open the rear door, remove the air filter, and turn off the general switch of the

smart cooling product.

Step 3 Disconnect the interconnection terminals from the actuator and ensure that the

actuator cable is separated from the smart cooling product.
1. Press the actuator button, as shown by (1) in 

Figure 6-19

.

Figure 6-19 Removing a chilled water valve actuator

2. Manually set the chilled water valve opening to the maximum (100%), as

shown by (2) in 

Figure 6-19

.

3. Insert a Phillips screwdriver into the hole right in front of the actuator, and

turn the screwdriver in the specified direction to unscrew the actuator, as

shown by (3) in 

Figure 6-19

.

Step 4 Install the new water valve actuator by performing 

Step 3.3

 to 

Step 2

, connect

the actuator cable, and then secure the cable using cable ties.

Step 5 Open the rear door, install the air filter, and turn on the power switch of the smart

cooling product.

NO TICE

The shaft of the new actuator must be installed in the same position where the

old actuator shaft is installed.

----End

NetCol5000-C(030, 032, 065) In-row Chilled Water

Smart Cooling Product

User Manual

6 System Operation and Maintenance

Issue 04 (2021-03-15)

Copyright © Huawei Technologies Co., Ltd.

170

Summary of Contents for NetCol5000-C030 Series
























































































































































































































Reviews:

No comments

Related manuals for NetCol5000-C030 Series

Manfrotto 504 Quick Manual preview
504
Brand: Manfrotto Pages: 4
TaylorMade M5 Tuning Manual preview
M5
Brand: TaylorMade Pages: 5
IHP PCBM-325 Manual preview
PCBM-325
Brand: IHP Pages: 8
Garmin GFS 10 - Fuel Sensor Configuration Manual preview
GFS 10 - Fuel Sensor
Brand: Garmin Pages: 2
Yakima K618 Instructions Manual preview
K618
Brand: Yakima Pages: 11
Manfrotto 331 Quick Start Manual preview
331
Brand: Manfrotto Pages: 2
Paradyne 7610 Overview preview
7610
Brand: Paradyne Pages: 2
La Crosse Technology TX5 Instruction Manual preview
TX5
Brand: La Crosse Technology Pages: 6
Valcom V-1109RTVA Brochure preview
V-1109RTVA
Brand: Valcom Pages: 1
Valcom V-1109RTHF User Manual preview
V-1109RTHF
Brand: Valcom Pages: 13
Valcom VIP-822 Manual preview
VIP-822
Brand: Valcom Pages: 3
Valcom VIP-814 User Manual preview
VIP-814
Brand: Valcom Pages: 4
Xerox 7500DX - Phaser Color LED Printer Instruction Sheet preview
7500DX - Phaser Color LED Printer
Brand: Xerox Pages: 5
FABBRI PORTATUTTO 17405400 Assembly Instructions preview
17405400
Brand: FABBRI PORTATUTTO Pages: 2
Adam CFW Series Service Manual preview
CFW Series
Brand: Adam Pages: 22
BS Bodensteckdosen Systemtechnik 85 E Series Instruction Manual preview
85 E Series
Brand: BS Bodensteckdosen Systemtechnik Pages: 14
hepco & becker 6537543 00 01 Mounting Instructions preview
6537543 00 01
Brand: hepco & becker Pages: 6
Ikan PBK-A-X Quick Start Manual preview
PBK-A-X
Brand: Ikan Pages: 2

Brands by name

Popular brands

Load more brands