Huawei NetCol5000-C030 Series User Manual Download

Page: 63 / 215

Figure 3-30 Combining cabinets

1. Remove the connecting kits from the cabinets.
2. Secure the connecting kits at the connection positions on the front door using

screws.

Step 3 Secure the connecting kits at the connection positions on the rear door using

screws in the same way.

NO TE

Ensure that the vertical distance between each device top and the floor is 2000 mm (±2

mm) or 2200 mm (±2 mm) and that all device tops are on the same plane.

----End

3.7 Securing the NetCol5000-C

3.7.1 Securing the Device (NetCol5000-C065)

Prerequisites

Secure the smart cooling product to the base. If there are no bases onsite, prepare

one by referring to

Figure B-1

Procedure

Step 1 Secure the device to the base.

NetCol5000-C(030, 032, 065) In-row Chilled Water

Smart Cooling Product

User Manual

3 Installation

Issue 04 (2021-03-15)

Summary of Contents for NetCol5000-C030 Series
























































































































































































































Search results

Summary of Contents for NetCol5000-C030 Series

Reviews:

Related manuals for NetCol5000-C030 Series

Brands by name

Popular brands

Huawei NetCol5000-C030 Series, User Manual

Search results

Summary of Contents for NetCol5000-C030 Series

Reviews:

Related manuals for NetCol5000-C030 Series

Brands by name

Popular brands