Huawei NetCol5000-C030 Series User Manual Download Page 88

Page: 88 / 215

Posit

ion

Name

Add

ress

DIP Switch ID

Hot aisle 3 temp/

humid

OFF

Hot aisle 4 temp/

humid

OFF

Hot aisle 5 temp/

humid

OFF

NO TICE

After the addresses are set, power on the device, choose Settings > System

Settings > T/H sensor on the home screen of the display module, and set the

sensors in the aisles corresponding to the addresses to Enable. Otherwise, the

sensors will not work.

----End

3.12.7 (Optional) Installing a Micro Differential Pressure

Sensor

Procedure

Step 1 Secure the micro differential pressure sensor and sheet metal to the cabinet using

M5 tapping screws.

Figure 3-70 Securing a differential pressure sensor (NetCol5000-C065)

NetCol5000-C(030, 032, 065) In-row Chilled Water

Smart Cooling Product

User Manual

3 Installation

Issue 04 (2021-03-15)

Summary of Contents for NetCol5000-C030 Series
























































































































































































































Search results

Summary of Contents for NetCol5000-C030 Series

Reviews:

Related manuals for NetCol5000-C030 Series

Brands by name

Popular brands

Huawei NetCol5000-C030 Series, User Manual

Search results

Summary of Contents for NetCol5000-C030 Series

Reviews:

Related manuals for NetCol5000-C030 Series

Brands by name

Popular brands