Huawei NetCol5000-C030 Series User Manual Download Page 122

Page: 122 / 215

Figure 4-21 Entering the startup password

NO TE

For offline startup, scan the QR code in the figure to enter the barcode and

verification code on the app.

●

If the screen shown in

Figure 4-22

is displayed, tap Confirm to start the

smart cooling product.

Figure 4-22 Startup

Step 2 Select

Offline Boot

Online Boot

as required on the Service Expert app for

initial startup verification.

NO TICE

The Service Expert app can be downloaded from Huawei app store and runs on

Android. User interfaces are for reference only.
● Offline boot: Enter the barcode and verification code on the mobile phone app

to generate a startup password, and start the smart cooling product on the

controller screen.

● Online boot: Activate the startup password on the mobile phone app to start

the smart cooling product online.

After factory settings are restored, re-verification for startup is required. For

details, see

Offline Boot

Online Boot

for verification.

----End

Offline Boot

Step 1 Open the Service Expert app.

NetCol5000-C(030, 032, 065) In-row Chilled Water

Smart Cooling Product

User Manual

4 Power-On Commissioning

Issue 04 (2021-03-15)

114

Summary of Contents for NetCol5000-C030 Series
























































































































































































































Search results

Summary of Contents for NetCol5000-C030 Series

Reviews:

Related manuals for NetCol5000-C030 Series

Brands by name

Popular brands

Huawei NetCol5000-C030 Series, User Manual

Search results

Summary of Contents for NetCol5000-C030 Series

Reviews:

Related manuals for NetCol5000-C030 Series

Brands by name

Popular brands