Huawei NetCol5000-C030 Series User Manual Download Page 119

Page: 119 / 215

●

When Indoor fan control type is set to Pressure diff ctrl, Air-side difference

pressure sensor type can not be set to No or 0~500Pa.

●

When Indoor fan control type is not set to Pressure diff ctrl, Air-side

difference pressure sensor type cannot be set to 0~500Pa.

Parameters of System Control

●

Cooling start temperature demand > Cooling stop temperature demand

●

Lower limit for dehumid start temperature demand > Lower limit for dehumid

close temperature demand

●

Upper limit for dehumid start temperature demand > Upper limit for dehumid

close temperature demand

4.6 Startup and Wizard Startup

4.6.1 First Startup Flowchart

Offline Boot or Online Boot can be selected for the first startup.

NO TICE

● Download the Service Expert app from HUAWEI AppGallery. The app can only

run on Android currently. You must apply for the permission to use the app

after downloading it.

● Indoor fan commissioning is a mandatory item for power-on commissioning.

Other components can be commissioned depending on actual requirements.

● If this is not the first startup, choose Maint > Wizard Startup to enter the

wizard startup mode.

● If no humidifier is configured, its commissioning item is not displayed.

NetCol5000-C(030, 032, 065) In-row Chilled Water

Smart Cooling Product

User Manual

4 Power-On Commissioning

Issue 04 (2021-03-15)

111

Summary of Contents for NetCol5000-C030 Series
























































































































































































































Search results

Summary of Contents for NetCol5000-C030 Series

Reviews:

Related manuals for NetCol5000-C030 Series

Brands by name

Popular brands

Huawei NetCol5000-C030 Series, User Manual

Search results

Summary of Contents for NetCol5000-C030 Series

Reviews:

Related manuals for NetCol5000-C030 Series

Brands by name

Popular brands