manualshive.com logo in svg

Huawei NetCol5000-C030 Series, User Manual

Introducing the Huawei NetCol5000-C030 Series, a cutting-edge cooling solution for data centers. Enhance your facility's efficiency with our state-of-the-art product. To swiftly set up and optimize your cooling system, download the comprehensive and free Quick Manual from manualshive.com. Experience seamless operations with this user-friendly manual at your fingertips.

Share
Download
background image

Alarm ID

Alarm Name

Alarm

Severity

Possible Cause

Solution

A007-01

Return air 2 temp/

humid sensor comm

failed
Cold aisle 1 temp/

humid sensor comm

failed
Cold aisle 2 temp/

humid sensor comm

failed
Cold aisle 3 temp/

humid sensor comm

failed
Cold aisle 4 temp/

humid sensor comm

failed
Cold aisle 5 temp/

humid sensor comm

failed
Hot aisle 1 temp/

humid sensor comm

failed
Hot aisle 2 temp/

humid sensor comm

failed
Hot aisle 3 temp/

humid sensor comm

failed
Hot aisle 4 temp/

humid sensor comm

failed
Hot aisle 5 temp/

humid sensor comm

failed

Major

● The cables to the

temperature and

humidity sensor are

loose or damaged.

● The DIP switch of

the temperature

and humidity

sensor is set

incorrectly.

● The temperature

and humidity

sensor is faulty.

● The

communications

port of the main

control board is

faulty.

1. Check the cables to

the temperature

and humidity

sensor.

2. Set the DIP switch

of the temperature

and humidity

sensor correctly.

3. Maintain or replace

the temperature

and humidity

sensor.

4. Maintain or replace

the main control

board.

NetCol5000-C(030, 032, 065) In-row Chilled Water

Smart Cooling Product

User Manual

6 System Operation and Maintenance

Issue 04 (2021-03-15)

Copyright © Huawei Technologies Co., Ltd.

135

Summary of Contents for NetCol5000-C030 Series
























































































































































































































Reviews:

No comments

Related manuals for NetCol5000-C030 Series

Y-cam Camera Assembly Instructions Manual preview
Camera
Brand: Y-cam Pages: 12
Samsung MWR-WW10N User Manual preview
MWR-WW10N
Brand: Samsung Pages: 60
Taffio CH7102-FCX9 Quick Start Manual preview
CH7102-FCX9
Brand: Taffio Pages: 8
Sacred Sun FMJ Series Technical Manual preview
FMJ Series
Brand: Sacred Sun Pages: 19
Microlife IFR 100 Instructions Manual preview
IFR 100
Brand: Microlife Pages: 121
DEFA WarmUp 411702 Fitting Instructions Manual preview
WarmUp 411702
Brand: DEFA Pages: 9
rough country Slim Line LED Light Grille Kit Manual preview
Slim Line LED Light Grille Kit
Brand: rough country Pages: 8
Blue Ox BX3781 Installation Instructions Manual preview
BX3781
Brand: Blue Ox Pages: 7
Shad NADSA ATV80 Owner'S Manual preview
NADSA ATV80
Brand: Shad Pages: 3
Dakota Digital MCL-36K-SPD Installation Manual preview
MCL-36K-SPD
Brand: Dakota Digital Pages: 6
Haibang HA998 Series Installation Instructions Manual preview
HA998 Series
Brand: Haibang Pages: 6
Alpha Alpha Top Easy-Flue 500 mm Installation Instructions Manual preview
Alpha Top Easy-Flue 500 mm
Brand: Alpha Pages: 6
Metra Electronics 95-8202 Installation Instructions Manual preview
95-8202
Brand: Metra Electronics Pages: 20
V-TAC SMART LIGHT VT-5050 Installation Instruction preview
SMART LIGHT VT-5050
Brand: V-TAC Pages: 20
First Alert PIR720R User Manual preview
PIR720R
Brand: First Alert Pages: 1
BRUUDT Yamaha X-MAX 300 Mounting Instructions preview
Yamaha X-MAX 300
Brand: BRUUDT Pages: 7
Hudora Kicker Kick It Manual preview
Kicker Kick It
Brand: Hudora Pages: 12
hepco & becker 6504513 01 01 Manual preview
6504513 01 01
Brand: hepco & becker Pages: 4

Brands by name

Popular brands

Load more brands