Huawei NetCol5000-C030 Series User Manual Download Page 201

Page: 201 / 215

management, browsing and modifying parameters, software upgrade, and

data import and export.

●

Operator: The user name is operator and password is Changeme by default.

Operator has no rights for network security certification, Modbus, SNMP,

software upgrade, and fault information.

NO TE

If the software version is V200R001C00 or earlier, SNMP and Modbus-TCP are not

supported.

Procedure

Step 1 Change the login password.

1. Log in to the WebUI as an administrator.
2. Choose Maintenance > User Management. The user management page is

displayed.

3. Choose the admin user and click Modify. Reset the login password on the

displayed page and tap Confirm.

Figure 7-22 Changing the login password

4. Enter Login user password and click Submit.

Figure 7-23 Recertification

NetCol5000-C(030, 032, 065) In-row Chilled Water

Smart Cooling Product

User Manual

7 FAQ

Issue 04 (2021-03-15)

193

Summary of Contents for NetCol5000-C030 Series
























































































































































































































Search results

Summary of Contents for NetCol5000-C030 Series

Reviews:

Related manuals for NetCol5000-C030 Series

Brands by name

Popular brands

Huawei NetCol5000-C030 Series, User Manual

Search results

Summary of Contents for NetCol5000-C030 Series

Reviews:

Related manuals for NetCol5000-C030 Series

Brands by name

Popular brands