Huawei NetCol5000-C030 Series User Manual Download Page 98

Page: 98 / 215

Menu

Parameter

Description

Setting Rule

Comm

Setting

Modbus Comm

address

Enter the

communication

address planned for

the smart cooling

product. The NMS

communicates with

the smart cooling

product through this

address.

The communication

addresses of the two smart

cooling products connected

to the same NMS must be

different.

----End

4.3 Home Screen

You can tap the menu items, buttons, or icons on the screen to enter related

screens or perform operations, such as Running, Alarms, and Settings. The

controller main screen is shown in

Figure 4-3

NO TICE

The information in the screenshots is for reference only. The actual parameters

prevail.

Figure 4-3 Home screen

NetCol5000-C(030, 032, 065) In-row Chilled Water

Smart Cooling Product

User Manual

4 Power-On Commissioning

Issue 04 (2021-03-15)

Summary of Contents for NetCol5000-C030 Series
























































































































































































































Search results

Summary of Contents for NetCol5000-C030 Series

Reviews:

Related manuals for NetCol5000-C030 Series

Brands by name

Popular brands

Huawei NetCol5000-C030 Series, User Manual

Search results

Summary of Contents for NetCol5000-C030 Series

Reviews:

Related manuals for NetCol5000-C030 Series

Brands by name

Popular brands