Huawei NetCol5000-C030 Series User Manual Download Page 187

Page: 187 / 215

Figure 7-8 E-label

NO TE

● The Version Info screen displays version details of the display board, control board, and

temperature and humidity collection board. The E-label screen displays electronic labels

of the entire system, control board, display board, and temperature and humidity

collection board.

● When some T/H boards of the cold or hot aisles are enabled, T/H Board on the About >

Version Info screen, or T/H Board on the About > E-label screen shows the

information of these T/H boards.

● When some T/H boards of the cold or hot aisles are disabled, T/H Board on the About

> Version Info screen, or T/H Board on the About > E-label screen does not show the

information of these T/H boards.

----End

7.1.6 How Do I Check Teamwork Control Information?

Procedure

Step 1 On the home screen, choose

. The teamwork control information is

displayed, as shown in

Figure 7-9

NetCol5000-C(030, 032, 065) In-row Chilled Water

Smart Cooling Product

User Manual

7 FAQ

Issue 04 (2021-03-15)

179

Summary of Contents for NetCol5000-C030 Series
























































































































































































































Search results

Summary of Contents for NetCol5000-C030 Series

Reviews:

Related manuals for NetCol5000-C030 Series

Brands by name

Popular brands

Huawei NetCol5000-C030 Series, User Manual

Search results

Summary of Contents for NetCol5000-C030 Series

Reviews:

Related manuals for NetCol5000-C030 Series

Brands by name

Popular brands