Huawei NetCol5000-C030 Series User Manual Download Page 144

Page: 144 / 215

Alarm ID

Alarm Name

Alarm

Severity

Possible Cause

Solution

A025-01

Return air filter

blocked alarm

Warning

● Air filters are

blocked or dirty.

● The differential

pressure switch is

faulty.

● An inappropriate

threshold is set for

the differential

pressure switch.

● The pressure tube

of the differential

pressure switch is

blocked or

disconnected.

● The cables to the

differential pressure

switch are loose or

damaged.

1. Maintain or replace

the air filters.

2. Replace the

differential pressure

switch.

3. Adjust the

threshold set for

the differential

pressure switch.

4. Dredge or replace

the pressure tube.

5. Check the cables to

the differential

pressure switch.

A026-01

Return air filter exceed

runtime alarm

Warning

The accumulated

runtime of the air

filter exceeds the

alarm threshold.

Maintain or replace

the air filter and clear

the accumulated

runtime.

A027-01

Power loss alarm

Warning

The power supply is

cut off.

If power failure occurs

on the power system,

no maintenance is

needed. If it occurs in

other places, check the

power supply cables.

A040-01

PSU 1 power supply

abnormal
PSU 2 power supply

abnormal

Warning

The input power

cables of the PSU are

loose or damaged.

Check the input power

cables of the PSU.

A042-01

Remote shutdown

alarm

Critical

● The remote

shutdown dry

contact is triggered.

● The cables to the

remote shutdown

dry contact are

loose or damaged.

1. Check the status of

the remote

shutdown dry

contact.

2. Check the cables to

the remote

shutdown dry

contact.

NetCol5000-C(030, 032, 065) In-row Chilled Water

Smart Cooling Product

User Manual

6 System Operation and Maintenance

Issue 04 (2021-03-15)

136

Summary of Contents for NetCol5000-C030 Series
























































































































































































































Search results

Summary of Contents for NetCol5000-C030 Series

Reviews:

Related manuals for NetCol5000-C030 Series

Brands by name

Popular brands

Huawei NetCol5000-C030 Series, User Manual

Search results

Summary of Contents for NetCol5000-C030 Series

Reviews:

Related manuals for NetCol5000-C030 Series

Brands by name

Popular brands