www.AccessOneTechnologies.com
I
MPORTANT
U
SER
I
NFORMATION
:
Automatic gate systems provide user convenience and
limit vehicular traffic. Because these systems can
produce high levels of force, it is important that you
are aware of the potential hazards associated with the
system. Potential hazards may include pinch points,
entrapment positions, lack of proper pedestrian
access, blind spots for traffic visibility.
It is the joint responsibility of the designer, purchaser,
installer and end user to verify the system is properly
configured for its intended use. Be sure the installer
has instructed you on the proper operation of the gate
system before use. Be sure the installer trains you
about the basic functions of the required reversing
devices associated with the gate system and how to
properly test them. Reversing devices may include
reverse loops, sensing edges, photoelectric cells,
inherent reverse detection, and/or other external
devices.
WARNING - To reduce the risk of injury or death:
1. A moving gate can cause serious injury or death.
Read & follow all installation manuals, reference
manuals, and warning label instructions.
2. Vehicular gates are for vehicles only.
Pedestrians must use a separate entrance. Keep
all pedestrian traffic away from any vehicular
gate. No one should cross the path of a moving
gate.
3. Never allow children to operate or play with gate
controls. Never allow children to play in the
area of a gate system.
4. Access control devices must be placed far
enough from moving gates to prevent the user
from coming in contact with the gate while
operating the controls.
5. All activating devices must be installed in a clear
line-of-sight with the gate and its travel and
must be installed a minimum of 10 feet away
from the gate.
6. Outdoor or easily accessible controls shall have a
security feature to prevent unauthorized use.
7. Mount all operating devices clearly out of reach
of through gates.
8. Loops and vehicle sensors are for vehicle use
only and do not offer any type of pedestrian
protection.
9. DO NOT install this device unless all
potential hazards and pinch points have
been eliminated.
R
ESTRICTIONS
AND
L
IMITATIONS
:
Please read and follow all restrictions and understand
all limitations. Do not install this product if it exceeds
any limitation or does not abide to all guidelines or
restrictions.
1. This device is intended for vehicular traffic only.
Keep all pedestrian traffic including bicycles away
from any vehicular gate.
2. Do not use this product with motorcycles unless
proper safety photo beams and safety edges are
installed.
3. This product is a wireless device and subject to
occasional communication failures. Therefore
proper safety photo beams and safety edges must
be used in conjunction to the system.
4. Detection distance and performance will vary
based upon location of each application.
5. Average detection distance from the sensor is
approximately 8ft wide x 4ft deep x 3-4ft high. In
some occasions the distance may be less and in
some occasions the distance may be more.
6. Detection range is similar to a rectangular bubble
around the sensor.
7. This product is not recommended for applications
with commercial trucks with high trailers due to the
limited detection height.
8. This product is a wireless device and location of
the AP100 Relay Board and each Sensor will have
a significant effect on the performance. Try to
locate the devices with as much line of sight as
possible.
9. Large walls, steel fences, foliage, etc will hamper
the radio signal range. Try to avoid such hazards.
10. The system should be checked on a regular basis
by a trained and authorized installer.
IMPORTANT:
DO NOT PARK IN THE PATH OF THE GATE. This
unit will automatically retune and reset after detecting
for more than 14 minutes. This allow the gate to close
on a vehicle.
DO NOT allow children to play near, on or with
the gate, gate operator, or any of its controls.
!
No Pedestrians
No Children
No Bicycles
No High Bed
Read and follow all UL and Safety Standards before installing. Refer to the manual and qualified personnel
for assistance. DO NOT install this device unless all entrapment and pinch points are eliminated.
EZ
Loop
Revision 1.8A
WVD100
Wireless Vehicle Detector
AP100 Relay Board
S200 Sensor
ACCESS STATUS
ONE PROGRAM
Quick Reference
Installation Instructions
Program Instructions
