Huawei NetCol5000-C030 Series User Manual Download Page 113

Page: 113 / 215

Parameter

Setting Method

IP address

Set according to the actual plan.

Subnet mask

Set according to the actual plan.

Gateway

Set according to the actual plan.

Step 3 Tap Submit.

Step 4 On the home screen, choose Settings > Comm Settings > Modbus Settings.

Step 5 Set parameters for Modbus TCP by following instructions.

Table 4-10 Modbus TCP parameter settings

Parameter Setting

Setting Method

Link mode

Server,

Client, Server

and client

● If you set Link mode to Server, the smart

cooling product, as a server, supports two client

connection and establishes communication.

● If you set Link mode to Client, the smart

cooling product, as a client, can connect to a

remote server and establish communication.

● If you set Link mode to Server and client, the

smart cooling product, as a server, supports two

client connection and establishes

communication. In addition, the smart cooling

product, as a client, can connect to a remote

server and establish communication.

Client

encryption

Enable,

Disable

This parameter is configurable when Link mode is

set to Client.

Server

encryption

Enable,

Disable

This parameter is configurable when Link mode is

set to Server.

NMS IP

address

Enter the actual IP address of the NMS. IP

addresses of the display panel, NMS client, and

NMS server must be unique. This parameter is

configurable when Link mode is set to Client.

NMS port

number

It is recommended that you retain the default

value. If you need to change the value, enter a

value as required. This parameter is configurable

when Link mode is set to Client.

----End

4.5.4.3 Setting Communications Parameters (SNMP Protocol)

NetCol5000-C(030, 032, 065) In-row Chilled Water

Smart Cooling Product

User Manual

4 Power-On Commissioning

Issue 04 (2021-03-15)

105

Summary of Contents for NetCol5000-C030 Series
























































































































































































































Search results

Summary of Contents for NetCol5000-C030 Series

Reviews:

Related manuals for NetCol5000-C030 Series

Brands by name

Popular brands

Huawei NetCol5000-C030 Series, User Manual

Search results

Summary of Contents for NetCol5000-C030 Series

Reviews:

Related manuals for NetCol5000-C030 Series

Brands by name

Popular brands