Huawei NetCol5000-C030 Series User Manual Download Page 165

Page: 165 / 215

NO TE

For single-cabinet packaging and dual-cabinet packaging, the methods for removing air

filters are the same. Take dual-cabinet packaging as an example.

Step 3 Install the spare air filter and secure the baffle plate.

Step 4 Close and lock the rear door.

Step 5 Choose Maint > Performance Maint on the home screen to access the

Performance Maint screen. Then clear the air filter runtime.

----End

6.4.3 Replacing a Fan

Prerequisites

●

A fan needs to be replaced.

●

A spare fan of the same model is available and functional.

Context

Recommended tools: protective gloves, Phillips screwdriver, diagonal pliers, cable

tie

Preparation: Maintain from the front door.

Procedure

Step 1 Choose Maint > Fan Maintenance on the home screen of the display module to

locate the SN of the faulty fan, and tap Power Off.

Step 2 Open the front door, remove cables from the faulty fan, use a Phillips screwdriver

to remove the four screws from the faulty fan, and remove the faulty fan.

Figure 6-3 Removing a fan (NetCol5000-C065)

NetCol5000-C(030, 032, 065) In-row Chilled Water

Smart Cooling Product

User Manual

6 System Operation and Maintenance

Issue 04 (2021-03-15)

157

Summary of Contents for NetCol5000-C030 Series
























































































































































































































Search results

Summary of Contents for NetCol5000-C030 Series

Reviews:

Related manuals for NetCol5000-C030 Series

Brands by name

Popular brands

Huawei NetCol5000-C030 Series, User Manual

Search results

Summary of Contents for NetCol5000-C030 Series

Reviews:

Related manuals for NetCol5000-C030 Series

Brands by name

Popular brands