Huawei NetCol5000-C030 Series User Manual Download Page 87

Page: 87 / 215

Figure 3-69 Cables routed outside the cabinet (NetCol5000-C030/C032)

NO TE

● The T/H sensors should be 1.5 m above the ground (33 U).
● Each smart cooling product supports a maximum of ten T/H sensors.

Step 2 Set DIP switches of the T/H sensors.

Table 3-5 DIP switch settings on T/H sensors

Posit

ion

Name

Add

ress

DIP Switch ID

Cold

aisle

Cold aisle 1

temp/humid

OFF

Cold aisle 2

temp/humid

OFF

Cold aisle 3

temp/humid

OFF

Cold aisle 4

temp/humid

OFF

Cold aisle 5

temp/humid

OFF

Hot

aisle

Hot aisle 1 temp/

humid

OFF

Hot aisle 2 temp/

humid

OFF

NetCol5000-C(030, 032, 065) In-row Chilled Water

Smart Cooling Product

User Manual

3 Installation

Issue 04 (2021-03-15)

Summary of Contents for NetCol5000-C030 Series
























































































































































































































Search results

Summary of Contents for NetCol5000-C030 Series

Reviews:

Related manuals for NetCol5000-C030 Series

Brands by name

Popular brands

Huawei NetCol5000-C030 Series, User Manual

Search results

Summary of Contents for NetCol5000-C030 Series

Reviews:

Related manuals for NetCol5000-C030 Series

Brands by name

Popular brands