Huawei NetCol5000-C030 Series User Manual Download Page 132

Page: 132 / 215

WebUI

5.1 Preparations and WebUI Login

Prerequisites

●

Operating system: Windows 7 or later

●

Browser: Chrome, Firefox, Internet Explorer 9 or later The following uses

Internet Explorer as an example.

Procedure

Step 1 Connect a network cable between the PC network port and the FE port (protected

by a security mechanism) on smart cooling product.

Step 2 On the home screen, choose Settings > Comm Settings > IP Settings. Change IP

assigning mode to Manual, and set the IP address, subnet mask and default

gateway.

Step 3 Configure the PC IP address and the smart cooling product IP address in the same

network segment.

If the smart cooling product IP address is 192.168.0.10, subnet mask is

255.255.255.0, and default gateway is 192.168.0.1, set the PC IP address to

192.168.0.11, subnet mask to 255.255.255.0, and default gateway to 192.168.0.1.

Step 4 Set LAN parameters.

NO TE

● If the smart cooling product connects to a LAN and a proxy server has been selected,

perform

Step 4.3

and

Step 4.4

● If the smart cooling product connects to the Internet, and the PC in a LAN accesses the

Internet over a proxy server, do not perform

Step 4.3

and

Step 4.4

. Otherwise, you will

fail to access the WebUI.

1. Open the Internet Explorer and choose Tools > Internet Options.
2. Click the Advanced tab and select Use TLS1.1 and Use TLS1.2.

NetCol5000-C(030, 032, 065) In-row Chilled Water

Smart Cooling Product

User Manual

5 WebUI

Issue 04 (2021-03-15)

124

Summary of Contents for NetCol5000-C030 Series
























































































































































































































Search results

Summary of Contents for NetCol5000-C030 Series

Reviews:

Related manuals for NetCol5000-C030 Series

Brands by name

Popular brands

Huawei NetCol5000-C030 Series, User Manual

Search results

Summary of Contents for NetCol5000-C030 Series

Reviews:

Related manuals for NetCol5000-C030 Series

Brands by name

Popular brands