Huawei NetCol5000-C030 Series User Manual Download Page 194

Page: 194 / 215

Configurations of temperature and humidity alarms and main board alarms for

the air cooled devices comply with the following relationships:
●

Power underfrequency alarm threshold < Power overfrequency alarm

threshold

●

Backup power underfrequency alarm threshold < Backup power

overfrequency alarm threshold

●

Supply air high temperature alarm thr 5°C ≤ Return air high

temperature alarm threshold

●

Supply air high temperature alarm thr 5°C ≤ Hot aisle high

temperature alarm threshold

●

Cold aisle high temperature alarm thr 5°C ≤ Hot aisle high

temperature alarm threshold

●

Cold aisle high temperature alarm thr 5°C ≤ Return air high

temperature alarm threshold

●

Supply air low temperature alarm thr 5°C ≤ Return air low

temperature alarm threshold

Context

●

To set an alarm threshold, follow the instructions in this section.

●

The method for setting each alarm is the same. This section describes how to

set Threshold of Supply air high temperature alarm to 45.

●

If you need to change alarm settings, log in as the Admin user.

NO TICE

Be careful when configuring alarms. Only professional maintenance personnel can

change alarm settings.

Procedure

Step 1 Choose Settings > Alarm Settings > T/H Sensor on the home screen.

Figure 7-17

is displayed.

Figure 7-17 Setting alarm parameter 1

Step 2 Tap Threshold following Supply air high temperature alarm.

Step 3 Set the value to 45 and tap

, as shown in

Figure 7-18

NetCol5000-C(030, 032, 065) In-row Chilled Water

Smart Cooling Product

User Manual

7 FAQ

Issue 04 (2021-03-15)

186

Summary of Contents for NetCol5000-C030 Series
























































































































































































































Search results

Summary of Contents for NetCol5000-C030 Series

Reviews:

Related manuals for NetCol5000-C030 Series

Brands by name

Popular brands

Huawei NetCol5000-C030 Series, User Manual

Search results

Summary of Contents for NetCol5000-C030 Series

Reviews:

Related manuals for NetCol5000-C030 Series

Brands by name

Popular brands