Huawei NetCol5000-C030 Series User Manual Download Page 53

Page: 53 / 215

3.3 Installation Process

NO TICE

Remove the protective plastic bag from the cabinet only immediately before

installation. Do not remove the bag during equipment room renovation or

infrastructure construction; otherwise, dust may enter the cabinet and affect the

internal components.

Figure 3-15 Installation flowchart

3.4 Checking the Nitrogen Pressure

Context

●

The device has been injected with 0.2–0.6 MPa nitrogen before delivery. Check

the nitrogen pressure for nitrogen leakage.

●

You can open or close the exhaust valve using a flat-head screwdriver.

Procedure

Step 1 Open the door lock using a key, and open the cabinet rear door.

NetCol5000-C(030, 032, 065) In-row Chilled Water

Smart Cooling Product

User Manual

3 Installation

Issue 04 (2021-03-15)

Summary of Contents for NetCol5000-C030 Series
























































































































































































































Search results

Summary of Contents for NetCol5000-C030 Series

Reviews:

Related manuals for NetCol5000-C030 Series

Brands by name

Popular brands

Huawei NetCol5000-C030 Series, User Manual

Search results

Summary of Contents for NetCol5000-C030 Series

Reviews:

Related manuals for NetCol5000-C030 Series

Brands by name

Popular brands