Huawei NetCol5000-C030 Series User Manual Download Page 185

Page: 185 / 215

●

Enter the Status Summary screen to view the control or running status of

major components such as the chilled water valve and indoor fan.

●

Enter the Device Details screen and select a component to view the status of

the component.

Procedure

●

When viewing the component status through Status Summary, choose

Common Function > Status Summary or Running > Status Summary on

the home screen. The general component status screen is displayed.

Figure

7-3

shows the screen displayed after choosing Running > Status Summary.

Figure 7-3 Status summary

●

When querying component status through Device Details (using the T/H

sensor as an example), choose Running > Device Details > T/H Sensor on

the home screen to query the status of the T/H Sensor, as shown in

Figure

7-4

Figure 7-4 T/H Sensor

----End

7.1.4 How Do I Query System Parameters?

Procedure

●

Choose Common Function > Operating Info on the home screen, the related

screen is displayed.

NetCol5000-C(030, 032, 065) In-row Chilled Water

Smart Cooling Product

User Manual

7 FAQ

Issue 04 (2021-03-15)

177

Summary of Contents for NetCol5000-C030 Series
























































































































































































































Search results

Summary of Contents for NetCol5000-C030 Series

Reviews:

Related manuals for NetCol5000-C030 Series

Brands by name

Popular brands

Huawei NetCol5000-C030 Series, User Manual

Search results

Summary of Contents for NetCol5000-C030 Series

Reviews:

Related manuals for NetCol5000-C030 Series

Brands by name

Popular brands