Huawei NetCol5000-C030 Series User Manual Download Page 21

Page: 21 / 215

●

Wet film humidifier (optional): Lowers water quality requirements and

supports a long replacement interval, and saves energy by over 95%

compared with a traditional electrode humidifier.

High Reliability

●

Teamwork control: Enables smart cooling products to work in turn to avoid

competitive operating and supports dynamic cooling capacity allocation and

backup of the main control system.

●

Dual power supplies: When the active power supply fails, the standby power

supply takes over automatically. When the active power supply is recovered,

the power supply is automatically switched back to the active power supply.

●

The smart cooling product supports a wide input voltage range to adapt to

poor power grids.

●

Intelligent differential pressure control (optional): Solves the issue of hot

spots due to insufficient air volume to improve reliability.

●

Temperature and humidity sensor: A maximum of ten remote ambient

temperature and humidity sensors can be configured to monitor the

temperature and humidity of data centers, improving reliability.

High Compatibility

●

Power supply: The NetCol5000-C can run in the working condition where the

input system is 220 V to 240 V AC, single-phase, and 50 Hz or 60 Hz. They

can protect against overload and short circuits.

●

Control mode: The NetCol5000-C supports multiple control modes, including

air supply control, cold aisle control, return air control, hot aisle control, and

pressure differential control. You can select control modes based on the

characteristics of your data centers.

Intelligent Monitoring

●

Users can monitor and configure the smart cooling product on a client.

●

The smart cooling product provides a 7-inch thin film transistor (TFT) true-

color touchscreen to display the device running mode and status. You can set

system parameters using the touchscreen. This achieves good human-

machine interaction.

Quick Installation and Commissioning

●

After the equipment is leveled and secured onsite, users need only to connect

pipes and cables before starting the equipment.

●

Startup wizard: A startup wizard is provided to guide operators through the

commissioning process. The smart cooling product running data is collected

automatically, which helps O&M personnel evaluate the status of the key

components of the smart cooling product, and simplifies O&M.

Easy Maintenance

●

Real-time display: The cooling capacity, air volume, power, and fan speed can

be displayed in real time on the control panel, which helps O&M personnel

grasp the running status of smart cooling products.

NetCol5000-C(030, 032, 065) In-row Chilled Water

Smart Cooling Product

User Manual

2 Product Description

Issue 04 (2021-03-15)

Summary of Contents for NetCol5000-C030 Series
























































































































































































































Search results

Summary of Contents for NetCol5000-C030 Series

Reviews:

Related manuals for NetCol5000-C030 Series

Brands by name

Popular brands

Huawei NetCol5000-C030 Series, User Manual

Search results

Summary of Contents for NetCol5000-C030 Series

Reviews:

Related manuals for NetCol5000-C030 Series

Brands by name

Popular brands