Huawei NetCol5000-C030 Series User Manual Download Page 101

Page: 101 / 215

4.5 Initial Configuration

4.5.1 Setting Temperature and Humidity Values and

(Optional) Enabling T/H Sensors

Prerequisites

●

The T/H sensors outside the cabinet need to be enabled when they are

installed, otherwise, skip

Step 2

●

If you need to enable a humidity and temperature sensor, log in as the admin

user.

●

This section describes how to enable Cold aisle sensor 1.

Procedure

Step 1 On the home screen, choose Settings > System Settings > T/H sensor.

Figure 4-4

is displayed.

Figure 4-4 Setting temperature and humidity values

Step 2 Set Cold aisle sensor 1 to Enable.
Step 3 Set the temperature and humidity values by referring to

Table 4-4

NO TE

You are not recommended to modify the parameters not listed in

Table 4-4

NetCol5000-C(030, 032, 065) In-row Chilled Water

Smart Cooling Product

User Manual

4 Power-On Commissioning

Issue 04 (2021-03-15)

Summary of Contents for NetCol5000-C030 Series
























































































































































































































Search results

Summary of Contents for NetCol5000-C030 Series

Reviews:

Related manuals for NetCol5000-C030 Series

Brands by name

Popular brands

Huawei NetCol5000-C030 Series, User Manual

Search results

Summary of Contents for NetCol5000-C030 Series

Reviews:

Related manuals for NetCol5000-C030 Series

Brands by name

Popular brands