HP FlexNetwork 5130 HI series Command Reference Manual Download Page 96

Page: 96 / 306

Usage guidelines

Static link aggregation groups are unaware of information about the peer groups. As a result, the

Partner ID

field displays

None

or nothing for a static link aggregation group.

Examples

# Display brief information about all aggregation groups.

<Sysname> display link-aggregation summary

Aggregation Interface Type:

BAGG -- Bridge-Aggregation, RAGG -- Route-Aggregation

Aggregation Mode: S -- Static, D -- Dynamic

Loadsharing Type: Shar -- Loadsharing, NonS -- Non-Loadsharing

Actor System ID: 0x8000, 000f-e267-6c6a

AGG AGG Partner ID Selected Unselected Share

Interface Mode Ports Ports Type

-------------------------------------------------------------------------------

BAGG1 S none 1 0 Shar

BAGG10 D 0x8000, 000f-e267-57ad 2 0 Shar

<Sysname> display link-aggregation summary

Aggregation Interface Type:

BAGG -- Bridge-Aggregation, RAGG -- Route-Aggregation

Aggregation Mode: S -- Static, D -- Dynamic

Loadsharing Type: Shar -- Loadsharing, NonS -- Non-Loadsharing

Actor System ID: 0x8000, 000f-e267-6c6a

AGG AGG Partner ID Selected Unselected Individual Share

Interface Mode Ports Ports Ports Type

--------------------------------------------------------------------------------

RAGG10 S None 1 0 0 NonS

BAGG20 D 0x8000,00e0-fcff-ff01 2 0 0 Shar

Table 21 Command output

Field Description

Aggregation Interface Type

Aggregate interface type:

•

BAGG

—Layer 2.

•

RAGG

—Layer 3.

Aggregation Mode

Aggregation group type:

•

—Static.

•

—Dynamic.

Loadsharing Type

Load sharing type:

•

Shar

—Load sharing.

•

NonS

—Non-load sharing.

Actor System ID

Local system ID, which contains the local system LACP priority and the local
system MAC address.

AGG Interface

Type and number of the aggregate interface.

AGG Mode

Aggregation group type.

Partner ID

System ID of the peer system, which contains the peer system LACP priority
and the peer system MAC address.

Summary of Contents for FlexNetwork 5130 HI series



















































































































































































































































































































Search results

Summary of Contents for FlexNetwork 5130 HI series

Reviews:

Related manuals for FlexNetwork 5130 HI series

Brands by name

Popular brands

HP FlexNetwork 5130 HI series, Command Reference Manual

Search results

Summary of Contents for FlexNetwork 5130 HI series

Reviews:

Related manuals for FlexNetwork 5130 HI series

Brands by name

Popular brands