HP FlexNetwork 5130 HI series Command Reference Manual Download Page 91

Page: 91 / 306

Field Description

conditions exist:

•

The data link layer protocol state of an interface
is shown as

•

The link is an on-demand link or not present.

Interface

Abbreviated interface name.

Link

Physical link state of the interface.

Speed

Interface speed, in bps.

Cause

Cause of a DOWN physical link.

display lacp system-id

Use

display lacp system-id

to display the system ID of the local system.

Syntax

display lacp system-id

Views

Any view

Predefined user roles

network-admin

network-operator

Usage guidelines

You can use the

lacp system-priority

command to change the LACP priority of the local system.

The LACP priority value is specified in decimal format in the

lacp system-priority

command.

However, it is displayed as a hexadecimal value in the output from the

display lacp system-id

command.

Examples

# Display the local system ID.

<Sysname> display lacp system-id

Actor System ID: 0x8000, 0000-fc00-6504

Table 18 Command output

Field Description

Actor System ID: 0x8000, 0000-fc00-6504

Local system ID, which contains the system LACP priority
(0x8000 in this sample output) and the system MAC address
(0000-FC00-6504 in this sample output).

Related commands

lacp system-priority

display link-aggregation load-sharing mode

Use

display link-aggregation load-sharing mode

to display global or group-specific

link-aggregation load sharing modes.

Summary of Contents for FlexNetwork 5130 HI series



















































































































































































































































































































Search results

Summary of Contents for FlexNetwork 5130 HI series

Reviews:

Related manuals for FlexNetwork 5130 HI series

Brands by name

Popular brands

HP FlexNetwork 5130 HI series, Command Reference Manual

Search results

Summary of Contents for FlexNetwork 5130 HI series

Reviews:

Related manuals for FlexNetwork 5130 HI series

Brands by name

Popular brands