manualshive.com logo in svg

HP FlexNetwork 5130 HI series, Command Reference Manual

Share
Download
HP FlexNetwork 5130 HI series Command Reference Manual Download Page 9

1 

Ethernet interface commands 

Common Ethernet interface commands 

bandwidth 

Use 

bandwidth

 to configure the expected bandwidth of an interface. 

Use 

undo bandwidth 

to restore the default. 

Syntax 

bandwidth

 

bandwidth-value 

undo bandwidth 

Default 

The expected bandwidth (in kbps) is the interface baud rate divided by 1000. 

Views 

Ethernet interface view 

Predefined user roles 

network-admin 

Parameters 

bandwidth-value

: Specifies the expected bandwidth in the range of 1 to 400000000 kbps.  

Usage guidelines 

The expected bandwidth of an interface affects the following items: 

•

 

Bandwidth assignment with CBQ. For more information, see 

ACL and QoS Configuration 

Guide

. 

Examples  

# Set the expected bandwidth of interface GigabitEthernet 1/0/1 to 1000 kbps. 

<Sysname> system-view 

[Sysname] interface gigabitethernet 1/0/1 

[Sysname-GigabitEthernet1/0/1] bandwidth 1000 

Related commands 

speed

 

default 

Use 

default

 to restore the default settings for an Ethernet interface. 

Syntax 

default 

Views 

Ethernet interface view 

Predefined user roles 

network-admin 

Summary of Contents for FlexNetwork 5130 HI series



















































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands