manualshive.com logo in svg

HP FlexNetwork 5130 HI series, Command Reference Manual

Share
Download
HP FlexNetwork 5130 HI series Command Reference Manual Download Page 282

 

274 

[Sysname] interface gigabitethernet 1/0/1 

[Sysname-GigabitEthernet1/0/1] lldp encapsulation snap 

lldp fast-count 

Use 

lldp fast-count

 to set the number of LLDP frames sent each time fast LLDP frame transmission 

is triggered. 

Use 

undo lldp fast-count

 to restore the default. 

Syntax 

lldp fast-count count 

undo lldp fast-count

 

Default 

The number is 4. 

Views 

System view 

Predefined user roles 

network-admin 

Parameters 

count

: Sets the number of LLDP frames sent each time fast LLDP frame transmission is triggered. 

The value range is 1 to 8. 

Examples 

# Configure the device to send five LLDP frames each time fast LLDP frame transmission is 
triggered. 

<Sysname> system-view 

[Sysname] lldp fast-count 5 

lldp global enable 

Use 

lldp global enable

 to enable LLDP globally. 

Use 

undo lldp global enable

 to disable LLDP globally. 

Syntax 

lldp global enable 

undo lldp global enable

 

Default 

If the switch starts up with empty configuration, LLDP is disabled globally (initial setting). 

If the switch starts up with the default configuration file, LLDP is enabled globally (factory default). 

For more information about empty configuration and the default configuration file, see 

Fundamentals 

Configuration Guide

. 

Views 

System view 

Predefined user roles 

network-admin 

Summary of Contents for FlexNetwork 5130 HI series



















































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands