HP FlexNetwork 5130 HI series Command Reference Manual Download Page 266

Page: 266 / 306

258

LLDP neighbor index : 6

ChassisID/subtype : 0011-2233-4400/MAC address

PortID/subtype : 000c-29f5-c715/MAC address

Capabilities : None

CDP neighbor-information of port 52[GigabitEthernet1/0/3]:

LLDP agent nearest-bridge:

CDP neighbor index : 4

Chassis ID : SEP00260B5C0548

Port ID : Port 1

CDP neighbor index : 5

Chassis ID : 0011-2233-4400

Port ID : GigabitEthernet1/0/4

LLDP neighbor-information of port 52[GigabitEthernet1/0/3]:

LLDP agent nearest-nontpmr:

LLDP neighbor index : 6

ChassisID/subtype : 0011-2233-4400/MAC address

PortID/subtype : 000c-29f5-c715/MAC address

Capabilities : None

# Display the brief LLDP information that all LLDP agents received from all neighboring devices in a
list.

<Sysname> display lldp neighbor-information list

Chassis ID : * -- --Nearest nontpmr bridge neighbor

# -- --Nearest customer bridge neighbor

Default -- -- Nearest bridge neighbor

System Name Local Interface Chassis ID Port ID

System1 GE1/0/1 000f-e25d-ee91 GigabitEthernet1/0/5

System2 GE1/0/2 000f-e25d-ee92* GigabitEthernet1/0/6

System3 GE1/0/3 000f-e25d-ee93# GigabitEthernet1/0/7

Table 58 Command output

Field Description

LLDP neighbor-information of port 1

LLDP information received through port 1.

Update time

Time when LLDP information about a neighboring device was last
updated.

Chassis type

Chassis ID type:

•

Chassis component

•

Interface alias

•

Port component

•

MAC address

•

Network address (ipv4)

•

Interface name

•

Locally assigned

—Locally-defined chassis type other than

those listed above.

Chassis ID

ID that identifies the LLDP sending device, which can be a MAC
address, a network address, an interface, or some other value,

Summary of Contents for FlexNetwork 5130 HI series



















































































































































































































































































































Search results

Summary of Contents for FlexNetwork 5130 HI series

Reviews:

Brands by name

Popular brands

HP FlexNetwork 5130 HI series, Command Reference Manual

Search results

Summary of Contents for FlexNetwork 5130 HI series

Reviews:

Brands by name

Popular brands