HP FlexNetwork 5130 HI series Command Reference Manual Download Page 68

Page: 68 / 306

Related commands

mac-address notification mac-move

display mac-address statistics

Use

display mac-address

statistics

to display MAC address table statistics.

Syntax

display mac-address

statistics

Views

Any view

Predefined user roles

network-admin

network-operator

Usage guidelines

This command displays the number of MAC address entries per type and the maximum number of
MAC address entries allowed for each type.

Examples

# Display MAC address table statistics.

<Sysname> display mac-address statistics

MAC Address Count

Dynamic Unicast Address (Learned) Count:

Dynamic Unicast Address (Security-service-defined) Count: 2

Static Unicast Address (User-defined) Count: 0

Static Unicast Address (System-defined) Count: 8

Total Unicast MAC Addresses In Use: 46

Total Unicast MAC Addresses Available: 32768

Multicast and Multiport MAC Address Count: 1

Static Multicast and Multiport MAC Address (User-defined) Count: 1

Total Multicast and Multiport MAC Addresses Available: 256

Table 16 Command output

Field Description

Dynamic Unicast Address (Learned) Count

Number of dynamic unicast MAC address entries
triggered by packets.

Dynamic Unicast Address (Security-service-defined)
Count

Number of dynamic unicast MAC address entries
triggered by the security service.

Static Unicast Address (User-defined) Count

Number of static unicast MAC address entries added
by users.

Static Unicast Address (System-defined) Count

Number of static unicast MAC address entries added
by the system.

Total Unicast MAC Addresses In Use

Number of unicast MAC address entries.

Total Unicast MAC Addresses Available

Maximum number of unicast MAC address entries
allowed.

Multicast and Multiport MAC Address Count

Number of multicast and multiport unicast MAC

Summary of Contents for FlexNetwork 5130 HI series



















































































































































































































































































































Search results

Summary of Contents for FlexNetwork 5130 HI series

Reviews:

Related manuals for FlexNetwork 5130 HI series

Brands by name

Popular brands

HP FlexNetwork 5130 HI series, Command Reference Manual

Search results

Summary of Contents for FlexNetwork 5130 HI series

Reviews:

Related manuals for FlexNetwork 5130 HI series

Brands by name

Popular brands