HP FlexNetwork 5130 HI series Command Reference Manual Download Page 173

Page: 173 / 306

165

This command might fail to restore the default settings for some commands for reasons such as
command dependencies or system restrictions. Use the

display this

command in interface view to

identify these commands, and then use their

undo

forms or follow the command reference to restore

their default settings. If your restoration attempt still fails, follow the error message instructions to
resolve the problem.

Examples

# Restore the default settings for VLAN-interface 1.

<Sysname> system-view

[Sysname] interface vlan-interface 1

[Sysname-Vlan-interface1] default

description

Use

description

to configure the description for a VLAN or VLAN interface.

Use

undo description

to restore the default.

Syntax

description text

undo description

Default

For a VLAN, the description is

VLAN

vlan-id.

The

vlan-id

argument specifies the VLAN ID in a

four-digit format. If the VLAN ID has fewer than four digits, leading zeros are added. For example, the
default description of VLAN 100 is

VLAN 0100

For a VLAN interface, the description is the name of the interface. For example,

Vlan-interface1

Interface

Views

VLAN view, VLAN interface view

Predefined user roles

network-admin

Parameters

text

: Specifies a description for a VLAN or VLAN interface, a string of 1 to 255 characters. The string

can include case-sensitive letters, digits, special symbols (see

Table 35

), spaces, and other Unicode

characters and symbols.

Table 35 Special symbols

Name Symbol

Tilde

Left angle bracket

Exclamation point

Right angle bracket

At sign

Hyphen

Pound sign

Underscore

Dollar sign

Plus sign

Percent sign

Equal sign

Caret

Vertical bar

Ampersand sign

Back slash

Asterisk

Colon

Summary of Contents for FlexNetwork 5130 HI series



















































































































































































































































































































Search results

Summary of Contents for FlexNetwork 5130 HI series

Reviews:

Related manuals for FlexNetwork 5130 HI series

Brands by name

Popular brands

HP FlexNetwork 5130 HI series, Command Reference Manual

Search results

Summary of Contents for FlexNetwork 5130 HI series

Reviews:

Related manuals for FlexNetwork 5130 HI series

Brands by name

Popular brands