manualshive.com logo in svg

HP FlexNetwork 5130 HI series, Command Reference Manual

The HP FlexNetwork 5130 HI series is a versatile network switch offering exceptional performance and flexibility. To maximize your user experience, you can conveniently access the comprehensive Command Reference Manual for free download from manualshive.com. Explore the extensive capabilities of this product with our user-friendly manual.

Share
Download
background image

8 

If you specify an interface type but do not specify an interface number, this command displays 
information about all interfaces of that type. 

If you specify both the interface type and interface number, this command displays information about 
the specified interface.  

Examples 

# Display information about Layer 2 interface GigabitEthernet 1/0/1. 

<Sysname> display interface gigabitethernet 1/0/1 

GigabitEthernet1/0/1                                                                    

Current state: UP                                                                

Line protocol state: UP                                                          

IP packet frame type: Ethernet II, hardware address: 0023-8927-ad7e 

Description: GigabitEthernet1/0/1 Interface                                      

Bandwidth: 1000000kbps                                                           

Loopback is not set                                                              

Media type is twisted pair                                                       

Port hardware type is 1000_BASE_T                                                

1000Mbps-speed mode, full-duplex mode                                            

Link speed type is autonegotiation, link duplex type is autonegotiation          

Flow-control is not enabled                                                      

The maximum frame length is 10000 

Allow jumbo frames to pass 

Broadcast max-ratio: 100% 

Multicast max-ratio: 100% 

Unicast max-ratio: 100% 

PVID: 1 

MDI type: automdix 

Port link-type: Access 

 Tagged VLANs:   None 

 UnTagged VLANs: 1 

Port priority: 0 

Last link flapping: Never  

Last clearing of counters: Never 

 Peak input rate: 14 bytes/sec, at 2013-01-01 06:32:27 

 Peak output rate: 552 bytes/sec, at 2013-01-01 06:32:27 

 Last 300 second input: 0 packets/sec 13 bytes/sec 0% 

 Last 300 second output: 1 packets/sec 245 bytes/sec 0% 

 Input (total):  1185 packets, 343696 bytes                                      

          0 unicasts, 2 broadcasts, 1183 multicasts, 0 pauses                    

 Input (normal):  1185 packets, - bytes                                          

          0 unicasts, 2 broadcasts, 1183 multicasts, 0 pauses                    

 Input:  0 input errors, 0 runts, 0 giants, 0 throttles                          

          0 CRC, 0 frame, - overruns, 0 aborts                                   

          - ignored, - parity errors                                             

 Output (total): 66479 packets, 14123537 bytes                                   

          592 unicasts, 35505 broadcasts, 30382 multicasts, 0 pauses             

 Output (normal): 66479 packets, - bytes                                         

          592 unicasts, 35505 broadcasts, 30382 multicasts, 0 pauses             

 Output: 0 output errors, - underruns, - buffer failures                         

Summary of Contents for FlexNetwork 5130 HI series



















































































































































































































































































































Reviews:

No comments

Related manuals for FlexNetwork 5130 HI series

D-Link DAP-1650 Quick Install Manual preview
DAP-1650
Brand: D-Link Pages: 16
D-Link DCH-G020 How-To preview
DCH-G020
Brand: D-Link Pages: 2
NETGEAR DS104 Installation Manual preview
DS104
Brand: NETGEAR Pages: 15
Eaton LPC25-16FUSE Instruction Leaflet preview
LPC25-16FUSE
Brand: Eaton Pages: 2
TESmart HDK0402A1U User Manual preview
HDK0402A1U
Brand: TESmart Pages: 12
AV-Box WUH5-H2 User Manual preview
WUH5-H2
Brand: AV-Box Pages: 11
CAMDEN Sure-Wave CM-330/N Installation Instructions preview
Sure-Wave CM-330/N
Brand: CAMDEN Pages: 4
Cabletron Systems CyberSWITCH CSX150 User Manual preview
CyberSWITCH CSX150
Brand: Cabletron Systems Pages: 620
Kobold PDD Series Operating Instructions Manual preview
PDD Series
Brand: Kobold Pages: 20
Rose electronics VISTA DVI Installation And Operation Manual preview
VISTA DVI
Brand: Rose electronics Pages: 16
Rose electronics UltraMatrix AV HD Installation And Operation Manual preview
UltraMatrix AV HD
Brand: Rose electronics Pages: 20
CYP CM-345TP Operation Manual preview
CM-345TP
Brand: CYP Pages: 12
SNAP Binary B-200-AVDMATRIX-6X4 Owner'S Manual preview
Binary B-200-AVDMATRIX-6X4
Brand: SNAP Pages: 8
Wyrestorm MX-0808-HDBT Instruction Manual preview
MX-0808-HDBT
Brand: Wyrestorm Pages: 24
SOMFY Inis 80 Technical Data Sheet preview
Inis 80
Brand: SOMFY Pages: 2
Fracarro AMP435SA Manual preview
AMP435SA
Brand: Fracarro Pages: 20
Hama USB 3.0 Hub 1:4 Operating Instruction preview
USB 3.0 Hub 1:4
Brand: Hama Pages: 12
ANTAIRA LNP-1002C-SFP-24 Series User Manual preview
LNP-1002C-SFP-24 Series
Brand: ANTAIRA Pages: 24

Brands by name

Popular brands

Load more brands