HP FlexNetwork 5130 HI series Command Reference Manual Download Page 255

Page: 255 / 306

247

Field Description

•

Many-to-one VLAN mapping

•

One-to-two VLAN mapping

Translated Outer VLAN

Translated outer VLAN.

This field indicates the translated VLAN when the

Translated Inner

VLAN

field displays

N/A

Translated Inner VLAN

Translated inner VLAN.

This field displays

N/A

for the following VLAN mapping types:

•

One-to-one VLAN mapping

•

Many-to-one VLAN mapping

Related commands

vlan

mapping

vlan mapping

Use

vlan

mapping

to configure VLAN mapping on an interface.

Use

undo

vlan

mapping

to cancel the VLAN mapping configuration.

Syntax

vlan

mapping

{

vlan-id translated-vlan

vlan-id

nest

{

range

vlan-range-list

single vlan-id-list

}

nested-vlan vlan-id

nni

tunnel outer-vlan-id inner-vlan-id translated-vlan outer-vlan-id

inner-vlan-id

uni

{

range

vlan-range-list

single

vlan-id-list

}

translated-vlan vlan-id

}

undo

vlan

mapping

{

vlan-id translated-vlan

vlan-id

all

nest

{

range

vlan-range-list

single

vlan-id-list

}

nested-vlan vlan-id

nni

tunnel outer-vlan-id inner-vlan-id translated-vlan

outer-vlan-id inner-vlan-id

uni

{

range

vlan-range-list

single

vlan-id-list

}

translated-vlan vlan-id

}

Default

VLAN mapping is not configured on an interface.

Views

Layer 2 Ethernet interface view, Layer 2 aggregate interface view

Predefined user roles

network-admin

Parameters

vlan-id

translated-vlan vlan-id

: Specifies the original VLAN and translated VLAN for a one-to-one

VLAN mapping. The value range for the

vlan-id

argument is 1 to 4094. The original VLAN and the

translated VLAN cannot be the same.

uni

range

vlan-range-list translated-vlan vlan-id

: Specifies the original VLAN ranges and the

translated VLAN for a many-to-one VLAN mapping on the customer-side port. The

vlan-range-list

argument specifies a space-separated list of up to 10 VLAN items. Each item specifies a VLAN ID or
a range of VLAN IDs in the form of

vlan-id1

vlan-id2

. The value range for VLAN IDs is 1 to 4094.

The value for the

vlan-id2

argument must be equal to or greater than the value for the

vlan-id1

argument.

Different VLAN ranges cannot overlap. Any of the original VLANs cannot be the same as

the translated VLAN.

uni

single

vlan-id-list translated-vlan vlan-id

: Specifies the original VLANs and the translated VLAN

for a many-to-one VLAN mapping on the customer-side port. The

vlan-id-list

argument specifies a

space-separated list of up to 10 VLAN IDs, each of which is in the range of 1 to 4094. The value
range for the

vlan-id

argument is 1 to 4094. Any of the original VLANs cannot be the same as the

translated VLAN.

Summary of Contents for FlexNetwork 5130 HI series



















































































































































































































































































































Search results

Summary of Contents for FlexNetwork 5130 HI series

Reviews:

Related manuals for FlexNetwork 5130 HI series

Brands by name

Popular brands

HP FlexNetwork 5130 HI series, Command Reference Manual

Search results

Summary of Contents for FlexNetwork 5130 HI series

Reviews:

Related manuals for FlexNetwork 5130 HI series

Brands by name

Popular brands