manualshive.com logo in svg

HP FlexNetwork 5130 HI series, Command Reference Manual

Share
Download
HP FlexNetwork 5130 HI series Command Reference Manual Download Page 108

 

100 

Default 

The load sharing mode is the same as the global load sharing mode. 

Views 

Layer 2 aggregate interface view 

Predefined user roles 

network-admin 

Parameters 

destination-ip

: Load shares traffic based on destination IP addresses. 

destination-mac

: Load shares traffic based on destination MAC addresses. 

source-ip

: Load shares traffic based on source IP addresses. 

source-mac

: Load shares traffic based on source MAC addresses. 

Usage guidelines 

The load sharing mode that you configure overwrites the previous mode. 

If an unsupported load sharing mode is configured, an error prompt appears. 

In Layer 2 aggregate interface view, the switch supports the following load sharing mode and 
combinations: 

•

 

Load sharing mode automatically determined based on the packet type. 

•

 

Source IP address. 

•

 

Destination IP address. 

•

 

Source MAC address. 

 

 

NOTE: 

Packets cannot be load shared based on source MAC addresses when the destination IP addresses
of the packets match multiport ARP entries. For more information about multiport ARP entries, see 

Layer 3—IP Services Configuration Guide

. 

 

•

 

Destination MAC address. 

•

 

Destination IP address and source IP address. 

•

 

Destination MAC address and source MAC address. 

Examples 

# Configure Layer 2 aggregation group 1 to load share packets based on destination MAC 
addresses.  

<Sysname> system-view 

[Sysname] interface bridge-aggregation 1 

[Sysname-Bridge-Aggregation1] link-aggregation load-sharing mode destination-mac 

Related commands 

link-aggregation global load-sharing mode 

link-aggregation load-sharing mode local-first 

Use 

link-aggregation load-sharing mode

 

local-first

 to enable local-first load sharing for link 

aggregation.  

Use 

undo link-aggregation load-sharing mode

 

local-first

 to disable local-first load sharing for link 

aggregation.  

Summary of Contents for FlexNetwork 5130 HI series



















































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands