manualshive.com logo in svg

HP FlexNetwork 5130 HI series, Command Reference Manual

Share
Download
HP FlexNetwork 5130 HI series Command Reference Manual Download Page 280

 

272 

Related commands 

lldp compliance cdp

 

lldp compliance cdp 

Use 

lldp compliance cdp

 to enable CDP compatibility globally.  

Use 

undo lldp compliance cdp

 to restore the default.  

Syntax 

lldp compliance cdp 

undo lldp compliance cdp

 

Default 

CDP compatibility is globally disabled.  

Views 

System view 

Predefined user roles 

network-admin 

Usage guidelines 

The maximum TTL that CDP allows is 255 seconds. To make CDP-compatible LLDP work correctly 
with Cisco IP phones, configure the LLDP frame transmission interval to be no more than 1/3 of the 
TTL value. 

Examples 

# Enable CDP compatibility globally.  

<Sysname> system-view 

[Sysname] lldp compliance cdp 

Related commands 

•

 lldp 

hold-multiplier

 

•

 

lldp timer tx-interval

 

lldp enable 

Use 

lldp enable

 to enable LLDP on a port. 

Use 

undo lldp enable

 to disable LLDP on a port. 

Syntax 

lldp enable 

undo lldp enable

 

Default 

LLDP is enabled on a port. 

Views 

Layer 2 aggregate interface view 

Layer 2 Ethernet interface view 

Management Ethernet interface view 

Summary of Contents for FlexNetwork 5130 HI series



















































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands