manualshive.com logo in svg

HP FlexNetwork 5130 HI series, Command Reference Manual

Share
Download
HP FlexNetwork 5130 HI series Command Reference Manual Download Page 123

 

115 

 Digest-Snooping     : Disabled 

 Rapid transition    : False 

 Num of VLANs mapped : 1 

 Port times          : Hello 2s MaxAge 20s FwdDelay 15s MsgAge 2s RemHops 20 

 BPDU sent           : 186 

          TCN: 0, Config: 0, RST: 0, MST: 186 

 BPDU received       : 0 

          TCN: 0, Config: 0, RST: 0, MST: 0 

 

-------[MSTI 1 Global Info]------- 

 Bridge ID         : 0.000f-e23e-9ca4 

 RegRoot ID/IRPC   : 0.000f-e23e-9ca4, 0 

 RootPort ID       : 0.0 

 Root type         : Primary root 

 Master bridge     : 32768.000f-e23e-9ca4 

 Cost to master    : 0 

 TC received       : 0 

# In PVST mode, display the spanning tree status and statistics for all ports in all VLANs. 

<Sysname> system-view 

[Sysname] stp mode pvst 

[Sysname] display stp 

-------[VLAN 1 Global Info]------- 

Protocol status     : Enabled 

Bridge ID           : 32768.000f-e200-2200 

Bridge times        : Hello 2s MaxAge 20s FwdDelay 15s 

VlanRoot ID/RPC     : 0.00e0-fc0e-6554, 200200 

RootPort ID         : 128.48 

BPDU-Protection     : Disabled 

TC or TCN received  : 2 

Time since last TC  : 0 days 0h:5m:42s 

 

 ----[Port1(Ethernet1/1)][FORWARDING]---- 

 Port protocol       : Enabled 

 Port role           : Designated Port 

 Port ID             : 128.153 

 Port cost(Legacy)   : Config=auto, Active=200 

 Desg. bridge/port   : 32768.000f-e200-2200, 128.2 

 Port edged          : Config=disabled, Active=disabled 

 Point-to-Point      : Config=auto, Active=true 

 Transmit limit      : 10 packets/hello-time 

 Protection type     : NONE 

 Rapid transition    : False 

 Port times          : Hello 2s MaxAge 20s FwdDelay 15s MsgAge 2s 

 

-------[VLAN 2 Global Info]------- 

Protocol status      : Enabled 

Bridge ID            : 32768.000f-e200-2200 

Bridge times         : Hello 2s MaxAge 20s FwDly 15s 

Summary of Contents for FlexNetwork 5130 HI series



















































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands