manualshive.com logo in svg

HP FlexNetwork 5130 HI series, Command Reference Manual

The HP FlexNetwork 5130 HI series is a versatile network switch offering exceptional performance and flexibility. To maximize your user experience, you can conveniently access the comprehensive Command Reference Manual for free download from manualshive.com. Explore the extensive capabilities of this product with our user-friendly manual.

Share
Download
background image

 

205 

    GigabitEthernet1/0/2            GigabitEthernet1/0/3 

 

 VLAN ID: 4 

 VLAN type: Static 

 Private VLAN type: Secondary 

 Route interface: Not configured 

 Description: VLAN 0004 

 Name: VLAN 0004 

 Tagged   ports: None 

 Untagged ports: 

    GigabitEthernet1/0/2            GigabitEthernet1/0/4 

Table 47 Command output 

Field Description 

VLAN type 

VLAN type: 

Dynamic

 or 

Static

. 

Private VLAN type 

Private VLAN type: 

•

 

Primary

—Primary VLAN.  

•

 

Secondary

—Secondary VLAN. 

•

 

Isolated secondary

—Secondary VLAN configured with port 

isolation at Layer 2.  

Route interface 

Whether the VLAN interface is configured for the VLAN: 

•

 Configured. 

•

 Not 

configured. 

IPv4 address 

Primary IPv4 address of the VLAN interface. This field is displayed only 
when an IPv4 address is configured for the VLAN interface.  

When the VLAN interface is also configured with secondary IPv4 
addresses, you can view them by using one of the following commands:

•

 

display interface vlan-interface

. 

•

 

display this

 (VLAN interface view). 

IPv4 subnet mask 

Subnet mask for the primary IPv4 address of the VLAN interface. This 
field is displayed only when an IPv4 address is configured for the VLAN 
interface. 

IPv6 global unicast addresses 

Global unicast IPv6 address of the VLAN interface. This field is not 
displayed when no IPv6 address is configured for the VLAN interface. 

The IPv6 address states are as follows: 

•

 

TENTATIVE

—Initial state. DAD is being performed or is to be 

performed on the address. An address in this state cannot be used 
as the source address or destination address of packets.  

•

 

DUPLICATE

—DAD has been completed for the address. The 

address is not unique on the link and cannot be used.  

•

 

PREFERRED

—The address is preferred and can be used as the 

source or destination address of a packet. If an address is in this 
state, the command does not display the address state. 

•

 

DEPRECATED

—The address is beyond the preferred lifetime but 

within the valid lifetime. It is valid, but it cannot be used as the 
source address for a new connection. Packets destined to the 
address are processed correctly. 

Description 

VLAN description.  

Name VLAN 

name. 

Tagged   ports 

Tagged members of the VLAN. 

Summary of Contents for FlexNetwork 5130 HI series



















































































































































































































































































































Reviews:

No comments

Related manuals for FlexNetwork 5130 HI series

UNICOM FEP-31024T-3 Specifications preview
FEP-31024T-3
Brand: UNICOM Pages: 1
Eaton P3-63/I4 Instruction Leaflet preview
P3-63/I4
Brand: Eaton Pages: 2
Raritan MCCAT18 Specifications preview
MCCAT18
Brand: Raritan Pages: 4
Cabletron Systems SynOptics 3000 Series Manual preview
SynOptics 3000 Series
Brand: Cabletron Systems Pages: 101
SMART-AVI RDU-8P Quick Start Manual preview
RDU-8P
Brand: SMART-AVI Pages: 2
LEGRAND Raritan Dominion LX II Quick Setup Manual preview
Raritan Dominion LX II
Brand: LEGRAND Pages: 7
Zamel GRG-01 Quick Start Manual preview
GRG-01
Brand: Zamel Pages: 2
ROSSMA IIOT-AMS Tilt Counter Operation Manual preview
IIOT-AMS Tilt Counter
Brand: ROSSMA Pages: 13
J-Tech Digital JTD-3003 User Manual preview
JTD-3003
Brand: J-Tech Digital Pages: 13
Kramer VS-24xl User Manual preview
VS-24xl
Brand: Kramer Pages: 11
Black Box LGB5028A Installation Manual preview
LGB5028A
Brand: Black Box Pages: 44
Omron ER1022 Datasheet preview
ER1022
Brand: Omron Pages: 4
ANTAIRA LMP-2012G-SFP Series Quick Installation Manual preview
LMP-2012G-SFP Series
Brand: ANTAIRA Pages: 2
Accton Technology 24/48 10/100 Ports + 2GE Management Manual preview
24/48 10/100 Ports + 2GE
Brand: Accton Technology Pages: 512
Tripp Lite B005-HUA4 Owner'S Manual preview
B005-HUA4
Brand: Tripp Lite Pages: 32
Pittway System Sensor EPS40 Series Installation And Maintenance Instructions preview
System Sensor EPS40 Series
Brand: Pittway Pages: 4
Makita Makstar BVR340 Instruction Manual preview
Makstar BVR340
Brand: Makita Pages: 40
Mitsubishi Electric 13J026 User Manual preview
13J026
Brand: Mitsubishi Electric Pages: 32

Brands by name

Popular brands

Load more brands