HP FlexNetwork 5130 HI series Command Reference Manual Download Page 278

Page: 278 / 306

270

Views

Layer 2 aggregate interface view

Layer 2 Ethernet interface view

Management Ethernet interface view

Predefined user roles

network-admin

Parameters

agent

: Specifies an LLDP agent type. If no agent type is specified in Ethernet interface view, the

command configures the operating mode for nearest bridge agents.

nearest-customer

: Specifies nearest customer bridge agents.

nearest-nontpmr

: Specifies nearest non-TPMR bridge agents.

disable

: Specifies the

Disable

mode. A port in this mode cannot send or receive LLDP frames.

: Specifies the

mode. A port in this mode can only receive LLDP frames.

: Specifies the

mode. A port in this mode can only send LLDP frames.

txrx

: Specifies the

TxRx

mode. A port in this mode can send and receive LLDP frames.

Examples

# Configure the LLDP operating mode as

for the nearest customer bridge agents on

GigabitEthernet 1/0/1.

<Sysname> system-view

[Sysname] interface gigabitethernet 1/0/1

[Sysname-GigabitEthernet1/0/1] lldp agent nearest-customer admin-status rx

lldp check-change-interval

Use

lldp check-change-interval

to enable LLDP polling and set the polling interval.

Use

undo lldp check-change-interval

to restore the default.

Syntax

In Layer 2 Ethernet interface view or management Ethernet interface view:

lldp

[

agent

{

nearest-customer

nearest-nontpmr

} ]

check-change-interval interval

undo lldp

[

agent

{

nearest-customer

nearest-nontpmr

} ]

check-change-interval

In Layer 2 aggregate interface view:

lldp agent

{

nearest-customer

nearest-nontpmr

}

check-change-interval interval

undo lldp agent

{

nearest-customer

nearest-nontpmr

}

check-change-interval

Default

LLDP polling is disabled.

Views

Layer 2 aggregate interface view

Layer 2 Ethernet interface view

Management Ethernet interface view

Predefined user roles

network-admin

Summary of Contents for FlexNetwork 5130 HI series



















































































































































































































































































































Search results

Summary of Contents for FlexNetwork 5130 HI series

Reviews:

Related manuals for FlexNetwork 5130 HI series

Brands by name

Popular brands

HP FlexNetwork 5130 HI series, Command Reference Manual

Search results

Summary of Contents for FlexNetwork 5130 HI series

Reviews:

Related manuals for FlexNetwork 5130 HI series

Brands by name

Popular brands