HP FlexNetwork 5130 HI series Command Reference Manual Download Page 199

Page: 199 / 306

191

all

: Removes all associations between the VLAN and IP subnets or IP addresses.

Usage guidelines

The IP subnet or IP address cannot be a multicast network segment or a multicast address.

Examples

# Configure VLAN 3 as an IP subnet-based VLAN and associate it with the 192.168.1.0/24 network
segment.

<Sysname> system-view

[Sysname] vlan 3

[Sysname-vlan3] ip-subnet-vlan ip 192.168.1.0 255.255.255.0

Related commands

•

display protocol-vlan interface

•

display

protocol-vlan

vlan

•

port

hybrid

protocol-vlan

port hybrid ip-subnet-vlan

Use

port hybrid ip-subnet-vlan

to associate a port with an IP subnet-based VLAN.

Use

undo port hybrid ip-subnet-vlan

to remove the association.

Syntax

port hybrid ip-subnet-vlan

vlan

vlan-id

undo

port hybrid ip-subnet-vlan

{

vlan

vlan-id

all

}

Default

A port is not associated with any IP subnet-based VLANs.

Views

Layer 2 Ethernet interface view, Layer 2 aggregate interface view

Predefined user roles

network-admin

Parameters

vlan vlan

: Specifies a VLAN by its ID in the range of 1 to 4094.

all

: Specifies all VLANs.

Usage guidelines

Only hybrid ports support this feature. Before you use this command, assign the port to the correct IP
subnet-based VLAN.

Examples

# Associate GigabitEthernet 1/0/1 with IP subnet-based VLAN 3.

<Sysname> system-view

[Sysname] vlan 3

[Sysname-vlan3] ip-subnet-vlan ip 192.168.1.0 255.255.255.0

[Sysname-vlan3] quit

[Sysname] interface gigabitethernet 1/0/1

[Sysname-GigabitEthernet1/0/1] port link-type hybrid

[Sysname-GigabitEthernet1/0/1] port hybrid vlan 3 untagged

Summary of Contents for FlexNetwork 5130 HI series



















































































































































































































































































































Search results

Summary of Contents for FlexNetwork 5130 HI series

Reviews:

Brands by name

Popular brands

HP FlexNetwork 5130 HI series, Command Reference Manual

Search results

Summary of Contents for FlexNetwork 5130 HI series

Reviews:

Brands by name

Popular brands