HP FlexNetwork 5130 HI series Command Reference Manual Download Page 286

Page: 286 / 306

278

Examples

# Configure LLDP to operate in service bridge mode.

<Sysname> system-view

[Sysname] lldp mode service-bridge

Related commands

lldp global enable

lldp notification med-topology-change enable

Use

lldp notification med-topology-change enable

to enable LLDP-MED trapping.

Use

undo lldp notification med-topology-change enable

to disable LLDP-MED trapping.

Syntax

lldp notification med-topology-change enable

undo lldp notification med-topology-change enable

Default

LLDP-MED trapping is disabled on ports.

Views

Layer 2 Ethernet interface view, management Ethernet interface view

Predefined user roles

network-admin

Examples

# Enable LLDP-MED trapping for GigabitEthernet 1/0/1.

<Sysname> system-view

[Sysname] interface gigabitethernet 1/0/1

[Sysname-GigabitEthernet1/0/1] lldp notification med-topology-change enable

lldp notification remote-change enable

Use

lldp notification remote-change enable

to enable LLDP trapping.

Use

undo lldp notification remote-change enable

to disable LLDP trapping.

Syntax

In Layer 2 Ethernet interface view or management Ethernet interface view:

lldp

[

agent

{

nearest-customer

nearest-nontpmr

} ]

notification remote-change enable

undo lldp

[

agent

{

nearest-customer

nearest-nontpmr

} ]

notification remote-change enable

In Layer 2 aggregate interface view:

lldp agent

{

nearest-customer

nearest-nontpmr

}

notification remote-change enable

undo lldp agent

{

nearest-customer

nearest-nontpmr

}

notification remote-change enable

Default

LLDP trapping is disabled on ports.

Views

Layer 2 aggregate interface view

Summary of Contents for FlexNetwork 5130 HI series



















































































































































































































































































































Search results

Summary of Contents for FlexNetwork 5130 HI series

Reviews:

Related manuals for FlexNetwork 5130 HI series

Brands by name

Popular brands

HP FlexNetwork 5130 HI series, Command Reference Manual

Search results

Summary of Contents for FlexNetwork 5130 HI series

Reviews:

Related manuals for FlexNetwork 5130 HI series

Brands by name

Popular brands