manualshive.com logo in svg

HP FlexNetwork 5130 HI series, Command Reference Manual

Share
Download
HP FlexNetwork 5130 HI series Command Reference Manual Download Page 141

 

133 

When the setting is configured on a member port in an aggregation group, it takes effect only after 
the port leaves the aggregation group.  

Examples 

# Enable Digest Snooping on GigabitEthernet 1/0/1 and then globally. 

<Sysname> system-view 

[Sysname] interface gigabitethernet 1/0/1 

[Sysname-GigabitEthernet1/0/1] stp config-digest-snooping 

[Sysname-GigabitEthernet1/0/1] quit 

[Sysname] stp global config-digest-snooping 

Related commands 

•

 display 

stp 

•

 

stp global config-digest-snooping 

stp cost 

Use 

stp cost 

to set the path cost of a port.  

Use 

undo stp cost 

to restore the default.  

Syntax 

stp 

[

 instance instance-list

 | 

vlan

 

vlan-id-list

 ]

 cost cost 

undo stp 

[

 instance instance-list

 | 

vlan

 

vlan-id-list

 ]

 cost 

Default 

The device automatically calculates the path costs of ports in each spanning tree based on the 
corresponding standard.  

Views 

Layer 2 Ethernet interface view, Layer 2 aggregate interface view 

Predefined user roles 

network-admin 

Parameters 

instance instance-list:

 Specifies a space-separated list of up to 10 MSTI items. Each item specifies 

an MSTI or a range of MSTIs in the form of 

instance-id1 

[ 

to

 

instance-id2

 ]. The value for 

instance-id2 

must be equal to or greater than the value for 

instance-id1

. The value range for the 

instance-id 

argument is 0 to 4094, and the value 0 represents the CIST. 

vlan

 

vlan-id-list

: Specifies a space-separated list of up to 10 VLAN items. Each item specifies a 

VLAN or a range of VLANs in the form of 

vlan-id1 

[ 

to

 

vlan-id2

 ]. The value for 

vlan-id2 

must be equal 

to or greater than the value for 

vlan-id1

. The value range for the 

vlan-id

 argument is 1 to 4094. 

cost

: Specifies the path cost of the port, with an effective range that depends on the path cost 

calculation standard that is used.  

•

 

When the IEEE 802.1d-1998 standard is selected for path cost calculation, the value range for 
the 

cost

 argument is 1 to 65535.  

•

 

When the IEEE 802.1t standard is selected for path cost calculation, the value range for the 

cost

 argument is 1 to 200000000.  

•

 

When the private standard is selected for path cost calculation, the value range for the 

cost

 

argument is 1 to 200000.  

Summary of Contents for FlexNetwork 5130 HI series



















































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands