HP FlexNetwork 5130 HI series Command Reference Manual Download Page 89

Page: 89 / 306

Output (normal): 1042508 packets, 133441832 bytes

1042306 unicasts, 0 broadcasts, 202 multicasts, 0 pauses

Output: 0 output errors, 0 underruns, 0 buffer failures

0 aborts, 0 deferred, 0 collisions, 0 late collisions

0 lost carrier, 0 no carrier

# Display brief information about Layer 2 aggregate interface Bridge-Aggregation 1.

<Sysname> display interface bridge-aggregation 1 brief

Brief information on interfaces in bridge mode:

Link: ADM - administratively down; Stby - standby

Speed: (a) - auto

Duplex: (a)/A - auto; H - half; F - full

Type: A - access; T - trunk; H - hybrid

Interface Link Speed Duplex Type PVID Description

BAGG1 UP auto A A 1

Table 17 Command output

Field Description

Bridge-Aggregation1

Layer 2 aggregate interface name.

Current state

Aggregate interface status:

•

DOWN (Administratively down)

—The

interface is administratively shut down with the

shutdown

command.

•

DOWN

—The interface is administratively up

but physically down (possibly because no
physical link is present or the link has failed).

•

—The Ethernet interface is both

administratively and physically up.

IP packet frame type

IPv4 packet frame format.

The value PKTFMT_ETHNT_2 indicates that
packets are encapsulated in Ethernet II format.

Description

Partial or complete interface description configured
by using the

description

command.

•

the

description

keyword is not specified in

the

display interface brief

command, this field

displays only the first 27 characters of the
interface description.

•

the

description

keyword is specified in the

display interface brief

command, this field

displays the complete interface description.

Bandwidth

Expected bandwidth of the interface.

Unknown-speed mode, unknown-duplex mode

The interface speed and duplex mode are unknown.

PVID

Port VLAN ID (PVID).

Port link-type

Port link type: access, trunk, or hybrid.

Tagged VLANs

Packets from the specified VLANs are sent out of
this interface with a VLAN tag:

•

Tagged Vlan: none

—All packets are sent out

of this interface without a VLAN tag.

•

Tagged Vlan: 1

—Packets from VLAN 1 are

sent out of this interface with a VLAN tag.

This field is displayed when the port link type is

Summary of Contents for FlexNetwork 5130 HI series



















































































































































































































































































































Search results

Summary of Contents for FlexNetwork 5130 HI series

Reviews:

Brands by name

Popular brands

HP FlexNetwork 5130 HI series, Command Reference Manual

Search results

Summary of Contents for FlexNetwork 5130 HI series

Reviews:

Brands by name

Popular brands