manualshive.com logo in svg

HP FlexNetwork 5130 HI series, Command Reference Manual

Share
Download
HP FlexNetwork 5130 HI series Command Reference Manual Download Page 216

 

208 

Predefined user roles 

network-admin 

Parameters 

vlan-id

: Specifies a VLAN ID in the range of 1 to 4094. Though VLAN 1 is in the valid value range, it 

cannot be configured in the command.  

Usage guidelines 

If the specified VLAN is a primary VLAN that has been associated with secondary VLANs, the 
command assigns the port to the associated secondary VLANs. Also, the following events occur: 

•

 

For an access port, the device performs the following tasks: 

{

 

Changes the port link type to hybrid. 

{

 

Configures the primary VLAN as the PVID.  

{

 

Assign the port to the primary VLAN and its associated secondary VLANs as an untagged 
member. 

•

 

For a trunk port, the device does not change the port link type or PVID.  

•

 

For a hybrid port, the device does not change the port link type or PVID.  

{

 

If the hybrid port has been a tagged or untagged member of the primary VLAN and part of its 
associated secondary VLANs, this member attribute remains in these VLANs. The device 
assigns the hybrid port to the rest of the associated secondary VLANs as an untagged 
member. 

{

 

If the hybrid port does not allow any of the primary VLAN and its associated secondary 
VLANs, the command assigns the port to these VLANs as an untagged member. 

If you execute this command on a promiscuous port, the system automatically executes the 

undo 

port private-vlan

 command and then the 

port private-vlan

 

promiscuous

 command.  

The 

undo port private-vlan

 command does not change the VLAN attributes (allowed secondary 

VLANs, link type, and PVID) of the port.  

When you execute the 

undo port private-vlan

 command on a promiscuous port of a VLAN, the 

command removes the port from the VLAN.  

You can configure the VLAN as a primary VLAN before or after you execute the 

port private-vlan

 

vlan-id

 

promiscuous

 command.  

The 

port private-vlan promiscuous

 command is mutually exclusive with the 

port private-vlan 

trunk promiscuous

 and 

port private-vlan trunk secondary

 commands.  

Examples 

In this example, VLAN 2 is a primary VLAN, and it is associated with secondary VLAN 20. 

# Display information about GigabitEthernet 1/0/1. 

<Sysname> system-view 

[Sysname] interface gigabitethernet 1/0/1 

[Sysname-GigabitEthernet1/0/1] display this 

# 

interface GigabitEthernet1/0/1 

# 

return 

# Configure GigabitEthernet 1/0/1 as a promiscuous port of primary VLAN 2, and then verify the 
configuration. 

[Sysname-GigabitEthernet1/0/1] port private-vlan 2 promiscuous 

[Sysname-GigabitEthernet1/0/1] display this 

# 

Summary of Contents for FlexNetwork 5130 HI series



















































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands