HP FlexNetwork 5130 HI series Command Reference Manual Download Page 296

Page: 296 / 306

288

A service loopback group must work with other features, such as GRE. It can be used by multiple
features.

You must create a service loopback group before you can use it with a feature.

You cannot change the service type of a service loopback group.

For correct traffic processing, do not delete a service loopback group that is being used by a feature.

Examples

# Create service loopback group 5 and specify the unicast tunnel service for the group.

<Sysname> system-view

[Sysname] service-loopback group 5 type tunnel

Summary of Contents for FlexNetwork 5130 HI series



















































































































































































































































































































Search results

Summary of Contents for FlexNetwork 5130 HI series

Reviews:

Related manuals for FlexNetwork 5130 HI series

Brands by name

Popular brands

HP FlexNetwork 5130 HI series, Command Reference Manual

Search results

Summary of Contents for FlexNetwork 5130 HI series

Reviews:

Related manuals for FlexNetwork 5130 HI series

Brands by name

Popular brands