HP FlexNetwork 5130 HI series Command Reference Manual Download Page 88

Page: 88 / 306

Predefined user roles

network-admin

network-operator

Parameters

bridge-aggregation

: Specifies Layer 2 aggregate interfaces.

interface-number

: Specifies an existing aggregate interface number. The value range for the

interface-number

argument is the set of all existing aggregate interface numbers.

brief

: Displays brief interface information. If you do not specify this keyword, the command displays

detailed interface information.

down

: Displays information about interfaces in down state and the causes for the down state. If you

do not specify this keyword, the command displays information about interfaces in all states.

description

: Displays complete interface descriptions. If you do not specify this keyword, the

command displays only the first 27 characters of each interface description.

Usage guidelines

If you do not specify the

bridge-aggregation

keywords, the command displays information about all

interfaces.

If you specify the

bridge-aggregation

keyword but do not specify an interface number, the

command displays information about all aggregate interfaces of the specified type.

If you specify the

bridge-aggregation

interface-number

option, the command displays information

about the specified aggregate interface.

Examples

# Display detailed information about Layer 2 aggregate interface Bridge-Aggregation 1.

<Sysname> display interface bridge-aggregation 1

Bridge-Aggregation1

Current state: UP

IP packet frame type: Ethernet II, hardware address: 000f-e207-f2e0

Description: Bridge-Aggregation1 Interface

Bandwidth: 0kbps

2Gbps-speed mode, full-duplex mode

Link speed type is autonegotiation, link duplex type is autonegotiation

PVID: 1

Port link-type: Access

Tagged VLANs: None

UnTagged VLANs: 1

Last clearing of counters: Never

Last 300 seconds input: 6900 packets/sec 885160 bytes/sec -%

Last 300 seconds output: 3150 packets/sec 404430 bytes/sec -%

Input (total): 5364747 packets, 686688416 bytes

2682273 unicasts, 1341137 broadcasts, 1341337 multicasts, 0 pauses

Input (normal): 5364747 packets, 686688416 bytes

2682273 unicasts, 1341137 broadcasts, 1341337 multicasts, 0 pauses

Input: 0 input errors, 0 runts, 0 giants, 0 throttles

0 CRC, 0 frame, 0 overruns, 0 aborts

0 ignored, 0 parity errors

Output (total): 1042508 packets, 133441832 bytes

1042306 unicasts, 0 broadcasts, 202 multicasts, 0 pauses

Summary of Contents for FlexNetwork 5130 HI series



















































































































































































































































































































Search results

Summary of Contents for FlexNetwork 5130 HI series

Reviews:

Related manuals for FlexNetwork 5130 HI series

Brands by name

Popular brands

HP FlexNetwork 5130 HI series, Command Reference Manual

Search results

Summary of Contents for FlexNetwork 5130 HI series

Reviews:

Related manuals for FlexNetwork 5130 HI series

Brands by name

Popular brands