HP FlexNetwork 5130 HI series Command Reference Manual Download Page 217

Page: 217 / 306

209

interface GigabitEthernet1/0/1

port link-type hybrid

port private-vlan 2 promiscuous

undo port hybrid vlan 1

port hybrid vlan 2 20 untagged

port hybrid pvid vlan 2

return

The output shows that:

•

GigabitEthernet 1/0/1 is a promiscuous port.

•

The port link type of GigabitEthernet 1/0/1 is hybrid and its PVID is VLAN 2.

•

GigabitEthernet 1/0/1 is an untagged member of primary VLAN 2 and secondary VLAN 20.

# Execute the

undo port private-vlan

command on GigabitEthernet 1/0/1, and then verify the

configuration.

[Sysname-GigabitEthernet1/0/1] undo port private-vlan

[Sysname-GigabitEthernet1/0/1] display this

interface GigabitEthernet1/0/1

port link-type hybrid

undo port hybrid vlan 1

port hybrid vlan 20 untagged

port hybrid pvid vlan 2

return

The output shows that:

•

The link type and PVID of GigabitEthernet 1/0/1 do not change.

•

GigabitEthernet 1/0/1 is an untagged member of VLAN 20.

•

GigabitEthernet 1/0/1 is removed from primary VLAN 2.

Related commands

•

port private-vlan host

•

port private-vlan trunk promiscuous

•

port private-vlan trunk secondary

•

private-vlan

(VLAN view)

•

private-vlan

primary

port private-vlan trunk promiscuous

Use

port private-vlan trunk promiscuous

to configure a port as a trunk promiscuous port of the

specified VLANs and assign the port to these VLANs.

Use

undo port private-vlan trunk promiscuous

to cancel the trunk promiscuous attribute of a port

in the specified VLANs.

Syntax

port private-vlan vlan-id-list

trunk promiscuous

undo port private-vlan

vlan-id-list

trunk promiscuous

Summary of Contents for FlexNetwork 5130 HI series



















































































































































































































































































































Search results

Summary of Contents for FlexNetwork 5130 HI series

Reviews:

Related manuals for FlexNetwork 5130 HI series

Brands by name

Popular brands

HP FlexNetwork 5130 HI series, Command Reference Manual

Search results

Summary of Contents for FlexNetwork 5130 HI series

Reviews:

Related manuals for FlexNetwork 5130 HI series

Brands by name

Popular brands