manualshive.com logo in svg

HP FlexNetwork 5130 HI series, Command Reference Manual

Share
Download
HP FlexNetwork 5130 HI series Command Reference Manual Download Page 268

 

260 

Field Description 

P0-   P1-   P2-   P3-   P4-   P5-   P6-  
P7- 

Number of supported priorities configured by using the 

priority-flow-control no-drop dot1p dot1p-list

 command on the 

neighbor. 

CoS map 

Application protocol-to-CoS mapping. 

CBS 

Indicates whether the token bucket mechanism is supported on 
the port: 

•

 

False

—The token bucket mechanism is not supported. 

•

 

True

—The token bucket mechanism is supported. 

Max TCs 

Maximum number of priorities supported. 

TSA 

Transmission selection algorithm. 

Value of MBC 

MBC indicates the ability of packets to bypass MACsec. It is 1-bit 
long. 

•

 

0

—Packets can bypass MACsec when MACsec is disabled.

•

 

1

—Packets cannot bypass MACsec when MACsec is 

disabled. 

Port and protocol VLAN ID(PPVID) 

Port protocol VLAN ID.  

Port and protocol VLAN supported 

Indicates whether protocol VLAN is supported on the port. 

Port and protocol VLAN enabled 

Indicates whether protocol VLAN is enabled on the port. 

VLAN name of VLAN 12 

Name of VLAN 12. 

Auto-negotiation supported 

Indicates whether autonegotiation is supported on the port. 

Auto-negotiation enabled 

Indicates whether autonegotiation is enabled on the port. 

OperMau 

Speed and duplex state on the port. 

Power port class 

PoE port class: 

•

 

PSE

—Power sourcing equipment. 

•

 

PD

—Powered device. 

PSE power supported 

Indicates whether the device can operate as a PSE. 

PSE power enabled 

Indicates whether the device is operating as a PSE. 

PSE pairs control ability 

Indicates whether the pair selection ability is available. 

Power pairs 

Power supply mode:  

•

 

Signal

—Uses data pairs to supply power. 

•

 

Spare

—Uses spare pairs to supply power. 

Port power classification 

Power class of the PD: 

•

 Class 

0. 

•

 Class 

1. 

•

 Class 

2. 

•

 Class 

3. 

•

 Class 

4. 

Power type 

This field appears only on the devices that support PoE.  

PD type of an LLDP neighboring device that is a PD device: 

•

 

Type 1 PD

—Receives a power of 0 W to 15.4 W, a voltage of 

44 V to 57 V, and a current of up to 350 mA.  

•

 

Type 2 PD

—Receives a power of 0 W to 30 W, a voltage of 50 

V to 57 V, and a current of up to 600 mA. 

Power source 

This field appears only on the devices that support PoE.  

Summary of Contents for FlexNetwork 5130 HI series



















































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands