manualshive.com logo in svg

HP FlexNetwork 5130 HI series, Command Reference Manual

Share
Download
HP FlexNetwork 5130 HI series Command Reference Manual Download Page 186

 

178 

Default 

All access ports belong to VLAN 1. 

Views 

Layer 2 Ethernet interface view, Layer 2 aggregate interface view 

Predefined user roles 

network-admin 

Parameters 

vlan-id

: Specifies a VLAN by its ID in the range of 1 to 4094. 

Usage guidelines 

Before assigning an access port to a VLAN, make sure the VLAN has been created. 

•

 

The configuration made in Layer 2 Ethernet interface view applies only to the port. 

•

 

The configuration made in Layer 2 aggregate interface view applies to the aggregate interface 
and its aggregation member ports.  

{

 

If the system fails to apply the configuration to the aggregate interface, it stops applying the 
configuration to aggregation member ports.  

{

 

If the system fails to apply the configuration to an aggregation member port, it skips the port 
and moves to the next member port. 

Examples 

# Assign GigabitEthernet 1/0/1 to VLAN 3. 

<Sysname> system-view 

[Sysname] vlan 3 

[Sysname-vlan3] quit 

[Sysname] interface gigabitethernet 1/0/1 

[Sysname-GigabitEthernet1/0/1] port access vlan 3 

port hybrid pvid 

Use 

port hybrid pvid 

to configure the PVID of a hybrid port.  

Use 

undo port hybrid pvid 

to configure the PVID of a hybrid port as 1. 

Syntax 

port hybrid pvid vlan vlan-id

 

undo port hybrid pvid 

Default 

The PVID of a hybrid port is the ID of the VLAN to which the port belongs when its link type is 

access

. 

Views 

Layer 2 Ethernet interface view, Layer 2 aggregate interface view 

Predefined user roles 

network-admin 

Parameters 

vlan-id

: Specifies a VLAN by its ID in the range of 1 to 4094. 

Summary of Contents for FlexNetwork 5130 HI series



















































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands