manualshive.com logo in svg

HP FlexNetwork 5130 HI series, Command Reference Manual

Share
Download
HP FlexNetwork 5130 HI series Command Reference Manual Download Page 149

 

141 

Usage guidelines 

The MSTP mode is compatible with the RSTP mode, and the RSTP mode is compatible with the STP 
mode.  

The PVST mode's compatibility with other modes is as follows: 

•

 Access 

port

—The PVST mode is compatible with other modes in any VLAN. 

•

 

Trunk or hybrid port

—The PVST mode is compatible with other modes only in VLAN 1. 

Examples 

# Configure the spanning tree device to operate in STP mode.  

<Sysname> system-view 

[Sysname] stp mode stp 

Related commands 

•

 stp 

enable 

•

 

stp global enable 

•

 

stp global mcheck 

•

 stp 

mcheck 

•

 

stp vlan enable 

stp no-agreement-check 

Use 

stp no-agreement-check

 to enable No Agreement Check on a port. 

Use 

undo stp no-agreement-check

 to disable No Agreement Check on a port. 

Syntax 

stp no-agreement-check 

undo stp no-agreement-check 

Default 

No Agreement Check is disabled. 

Views 

Layer 2 Ethernet interface view, Layer 2 aggregate interface view 

Predefined user roles 

network-admin 

Usage guidelines 

This command takes effect only after you enable it on the root port. 

When the setting is configured in Layer 2 Ethernet interface view, it takes effect only on that 
interface.  

When the setting is configured in Layer 2 aggregate interface view, it takes effect only on the 
aggregate interface.  

When the setting is configured on a member port in an aggregation group, it takes effect only after 
the port leaves the aggregation group.  

Examples 

# Enable No Agreement Check on GigabitEthernet 1/0/1. 

<Sysname> system-view 

[Sysname] interface gigabitethernet 1/0/1 

Summary of Contents for FlexNetwork 5130 HI series



















































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands