manualshive.com logo in svg

HP FlexNetwork 5130 HI series, Command Reference Manual

Share
Download
HP FlexNetwork 5130 HI series Command Reference Manual Download Page 34

26 

Views 

Ethernet interface view 

Predefined user roles 

network-admin 

Parameters 

10

: Sets the interface speed to 10 Mbps.  

100

: Sets the interface speed to 100 Mbps.  

1000

: Sets the interface speed to 1000 Mbps. 

 

10000

: Sets the interface speed to 10000 Mbps.  

auto

: Enables the interface to negotiate a speed with its peer.  

Usage guidelines 

A GE SFP interface supports only keywords 

100

, 

1000

, and 

auto

. 

A GE copper port supports only keywords 

10

, 

100

, 

1000

, and 

auto

. 

A 10-GE SFP+ interface supports only keywords 

1000

, 

10000

, and 

auto

. 

A 10-GE copper port supports only keywords 

100

, 

1000

, 

10000

, and 

auto

. 

Interfaces on an HPE 5130/5510 10GbE SFP+ 2-port Module (JH157A) or HPE 5130/5510 
10GBASE-T 2-port Module (JH156A) interface card support only the 

10000

 keyword. 

For a fiber port, use the 

speed

 command to set its speed to match the rate of a transceiver module. 

Examples 

# Configure GigabitEthernet 1/0/1 to autonegotiate the speed. 

<Sysname> system-view 

[Sysname] interface gigabitethernet 1/0/1 

[Sysname-GigabitEthernet1/0/1] speed auto 

Related commands 

speed auto 

speed auto downgrade 

Use 

speed auto downgrade 

to enable automatic negotiation for speed downgrading. 

Use 

undo speed auto downgrade 

to disable automatic negotiation for speed downgrading. 

Syntax 

speed auto downgrade 

undo speed auto downgrade 

Default 

Automatic negotiation for speed downgrading is enabled. 

Views 

Ethernet interface view 

Predefined user roles 

network-admin 

Summary of Contents for FlexNetwork 5130 HI series



















































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands